manualshive.com logo in svg

AAON RSMD, Technical Manual

Share
Download
AAON RSMD Technical Manual Download Page 27

27

RSMD Technical Guide 

TROUBLESHOOTING

Temperature Sensor Testing

Thermistor Sensor Testing Instructions

Use the resistance column to check the thermistor sensor while 

disconnected from the controllers (not powered).

Use the voltage column to check sensors while connected to 

powered controllers. Read voltage with meter set on DC volts. 

Place the “-” (minus) lead on GND terminal and the “+” (plus) 

lead on the sensor input terminal being investigated.

If the voltage is above 4.88 VDC, then the sensor or wiring is 

“open.” If the voltage is less than 0.05 VDC, then the sensor or 

wiring is shorted.

Sensor Voltage and Resistance

The following sensor voltage and resistance table is provided to 

aid in checking sensors that appear to be operating incorrectly. 

See 

Table 5

, below. Many system operating problems can be 

traced to incorrect sensor wiring. Be sure all sensors are wired 

per the wiring diagrams in this manual. 

If the sensors still do not appear to be operating or reading 

correctly, check voltage and/or resistance to confirm that the 

sensor is operating correctly per the tables. Please follow the 

notes and instructions that appear after the chart when checking 

sensors.

Table 6:  0-5V Temperature Sensor - Voltage & Resistance for Type III Sensors

Temperature – Resistance – Voltage for Type III 10 K Ohm Thermistor Sensors

Temp

(ºF)

Temp

(ºC)

Resistance

(Ohms)

Voltage @ 

Input (VDC)

Temp

(ºF)

Temp

(ºC)

Resistance

(Ohms)

Voltage @ 

Input 

(VDC)

-10

-23.3

93333

4.51

72

22.2

11136

2.635

-5

-20.6

80531

4.45

73

22.8

10878

2.605

0

-17.8

69822

4.37

74

23.3

10625

2.576

5

-15

60552

4.29

75

23.9

10398

2.549

10

-12.2

52500

4.2

76

24.4

10158

2.52

15

-9.4

45902

4.1

77

25

10000

2.5

20

-6.6

40147

4.002

78

25.6

9711

2.464

25

-3.9

35165

3.891

80

26.7

9302

2.41

30

-1.1

30805

3.773

82

27.8

8893

2.354

35

1.7

27140

3.651

84

28.9

8514

2.3

40

4.4

23874

3.522

86

30

8153

2.246

45

7.2

21094

3.39

88

31.1

7805

2.192

50

10

18655

3.252

90

32.2

7472

2.139

52

11.1

17799

3.199

95

35

6716

2.009

54

12.2

16956

3.143

100

37.8

6047

1.884

56

13.3

16164

3.087

105

40.6

5453

1.765

58

14.4

15385

3.029

110

43.3

4923

1.65

60

15.6

14681

2.972

115

46.1

4449

1.54

62

16.7

14014

2.916

120

48.9

4030

1.436

64

17.8

13382

2.861

125

51.7

3656

1.339

66

18.9

12758

2.802

130

54.4

3317

1.246

68

20

12191

2.746

135

57.2

3015

1.159

69

20.6

11906

2.717

140

60

2743

1.077

70

21.1

11652

2.691

145

62.7

2502

1.001

71

21.7

11379

2.661

150

65.6

2288

0.931

Summary of Contents for RSMD











































Reviews:

No comments

Brands by name

Popular brands

Load more brands