manualshive.com logo in svg

AAON RSMD, Technical Manual

Share
Download
AAON RSMD Technical Manual Download Page 21

21

RSMD Technical Guide 

LCD SCREENS

Configuration and Diagnostic Screens

Configuration Screens

Refer to the following map when navigating through the 

Configuration  Screens.  From  the  CONFIG  Screen,  press 

<ENTER> 

to scroll through the screens.

CONFIG

COND FAN 

LOCKED/UNLOCKED

CONDENSER FAN LOCKED OR UNLOCKED

LOCK POS

100%

CONDENSER FAN LOCKED POSITION

Diagnostic Screens

Refer to the following map when navigating through the 

Diagnostic  Screens.  From  the  DIAGNSTC  Screen,  press 

<ENTER>

 to scroll through the screens.

DIAGNSTC

WDOG CNT 

#

WATCHDOG TIMER

Displays the numbers of times the board has been reset due to 

watchdog timer overview.

POWR CNT 

#

POWER LOSS COUNT

Displays the numbers of times the board has been reset due to 

power loss.

EPROM:

HOLD 

DOWN 

TO 

LOAD

DEFAULTS 

SP-1 VLT 

X.XX

SUCTION PRESSURE SENSOR 1 VOLTAGE

Displays the current voltage of the Suction Pressure Sensor 1.

HP-1 VLT 

X.XX

HEAD PRESSURE SENSOR 1 VOLTAGE

Displays the current voltage of the Head Pressure Sensor 1.

SP-2 VLT 

X.XX

SUCTION PRESSURE SENSOR 2 VOLTAGE

Displays the current voltage of the Suction Pressure Sensor 2.

HP-2 VLT 

X.XX

HEAD PRESSURE SENSOR 2 VOLTAGE

Displays the current voltage of the Head Pressure Sensor 2.

Summary of Contents for RSMD











































Reviews:

No comments

Brands by name

Popular brands

Load more brands