manualshive.com logo in svg

AAON RSMD, Technical Manual

Share
Download
AAON RSMD Technical Manual Download Page 14

14

      RSMD Technical Guide

LCD SCREENS

Main Screens Map and RSMD Module Screens

 RSMD Main Screens Map

Refer to the following map when navigating through the LCD 

Main Screens. To scroll through the screens, press the 

<MENU>

 

button.

 RSMD Module Screens

Refer to the following map when navigating through the RSMD 

Screens. From the RSMD Screen, press 

<ENTER>

 to scroll 

through the screens.

SENSOR
STATUS  

Press 

 to scroll through REFRIG MODULE screens.

Press 

 to go to SYSTEM STATUS screens.

SYSTEM
STATUS 

Press 

 to scroll through SYSTEM STATUS screens.

Press 

 to go to SENSOR STATUS screens.

SENSOR 
STATUS 

Press 

 to scroll through SENSOR STATUS screens.

Press 

 to go to ALARMS screens.

ALARMS

Press 

 to scroll through ALARMS screens.

Press 

 to go to ALARM HISTORY screens.

ALARM

HISTORY

Press 

 to scroll through ALARM HISTORY screens.

Press 

 to go to SETPOINT STATUS screens.

SETPOINT

STATUS

Press 

 to scroll through SETPOINT STATUS screens.

 RSMD

1067vxxx

EBUS COMM 

PACKETS

E-BUS COMMUNICATION DIAGNOSTICS

Number of COMM packets received.

SOFTWARE

1067vXXX

CURRENT SOFTWARE VERSION

You can access the protected screens from this screen by holding 

the 

<UP> 

button for 5 seconds.

BOARD/EBUS 

ADDRESS 

CURRENT BOARD ADDRESS

#COMP 

CONFIGURED

# OF COMPRESSORS CONFIGURED

#COND 

CONFIGURED

# OF CONDENSERS CONFIGURED

Summary of Contents for RSMD











































Reviews:

No comments

Brands by name

Popular brands

Load more brands