manualshive.com logo in svg

AAON RSMD, Technical Manual

Share
Download
AAON RSMD Technical Manual Download Page 17

17

RSMD Technical Guide 

LCD SCREENS

Setpoint Status Screens

Setpoint Status Screens

Refer to the following map when navigating through the Setpoint 

Status Screens. From the SETPOINT STATUS Screen, press 

<ENTER>

 to scroll through the screens.

SETPOINT 

STATUS

 COILT SP 

35 DEG 

 

 

COIL TEMPERATURE SETPOINT STATUS

Valid range is 35 to 70 degrees. Default is 35 degrees.

IF CONFIGURED FOR MODULATING CONDENSER, 

THE FOLLOWING SCREEN WILL DISPLAY

HEADPRSP 

340 PSI 

 

 

HEAD PRESSURE SETPOINT STATUS

Valid range is 275 to 475 PSI. Default is 340 PSI.

IF CONFIGURED FOR FAN CYCLE, THE 

FOLLOWING TWO SCREENS WILL DISPLAY

FAN ON

XX PSI

HEAD PRESSURE HEADING WHEN FAN CYCLE IS ON

FAN OFF 

XX PSI

HEAD PRESSURE READING WHEN FAN CYCLE IS OFF

IF CONFIGURED WATER SOURCE HEAT PUMP, 

THE FOLLOWING THREE SCREENS WILL DISPLAY

 GLYCOL % 

% 

 

 

GLYCOL PERCENTAGE STATUS

 LOW SUCT 

95 PSI 

 

 

LOW SUCTION PRESSURE SETPOINT STATUS

Default is 95 PSI.

 LOW H2O 

37 DEGF 

 

 

LOW LEAVING WATER TEMPERATURE SETPOINT STATUS

Default is 37ºF.

IF CONFIGURED FOR AIR TO AIR HEAT PUMP, 

THE FOLLOWING SCREEN WILL DISPLAY

 DEFR INT 

30 MIN 

 

 

DEFROST INTERVAL SETPOINT STATUS

Default is 30 minutes.

Summary of Contents for RSMD











































Reviews:

No comments

Brands by name

Popular brands

Load more brands