A&D FX-iWP Series Page 69 Instruction Manual Download

Page: 69 / 79

18. OPTIONS

Notes
The FX

-02, FX

-08 and FX

-09 can not be used at the same time.

The FX-

WP series balance does not comply with IP65 when the FX

-02, FX

-08 or FX

-09 is

used with the balance.

-02 USB interface (Installed in the balance, Applicable OS: Windows 98 OSR2 or later)

Used to transmit the balance weight data (numerical

value only) uni-directionally to a personal computer via
USB.

Can transmit the balance weight data (numerical value

only) directly to other application software such as
Microsoft Excel, Word and memo pad.

Driver installation is not necessary.

-08 Ethernet interface

Used to connect the balance to a LAN.

The "WinCT-Plus" data communication software is

provided as an accessory and can perform the
following.

Acquire data from multiple balances connected to a

LAN.

Control these balances with commands.
Acquire data transmitted from balances.

Example: When pressing the PRINT key of the balance,
data is output and is acquired by the computer.

The stored data can be used with Microsoft Excel (if

installed).

-09 Built-in battery unit (Ni-HM rechargeable battery pack)

Charging time: Approx. 10 hours
Continuous operation hours: Approx. 8 hours

–02

Example of use

–08 Example of use

Summary of Contents for FX-iWP Series
















































































Search results

Summary of Contents for FX-iWP Series

Reviews:

Related manuals for FX-iWP Series

Brands by name

Popular brands

A&D FX-iWP Series, Instruction Manual

Search results

Summary of Contents for FX-iWP Series

Reviews:

Related manuals for FX-iWP Series

Brands by name

Popular brands