A&D FX-iWP Series Page 13 Instruction Manual Download

Page: 13 / 79

AC adapter

ID label

RS-232C

serial interface

Main unit rear side

AC adapter jack

Grounding

terminal

AC adapter plug

Keys

Weighing pan

Main unit

Display

Main unit cove

Terminal cover

How to assemble the breeze break (Only for

FX-120

WP/200

WP/300

WP)

Assemble the breeze break as shown below.

Follow the numbered sequence.

Bubble spirit

level

Leveling foot

Pan support

Waterproof

diaphragm

Pan boss

2. UNPACKING THE BALANCE

2-1 Unpacking

The balance is a precision instrument. Unpack the balance carefully. Keep the packing

material to be used for transporting the balance in the future.

The packing contents depend on the balance model. See the illustrations to confirm that

everything is contained.

Note
Please confirm that the AC adapter type is correct
for your local voltage and receptacle type.

The AC adapter plug is

protected against dust

and may be difficult to

insert. When inserting

the plug, turn the plug

while pushing on it.

When attaching the pan

support, use much care not

to deform the diaphragm.

To use as a dust and waterproof

balance, cover the RS-232C

interface connector, or connect the

waterproof RS-232C cable

(AX-KO0273-500).

Summary of Contents for FX-iWP Series
















































































Search results

Summary of Contents for FX-iWP Series

Reviews:

Related manuals for FX-iWP Series

Brands by name

Popular brands

A&D FX-iWP Series, Instruction Manual

Search results

Summary of Contents for FX-iWP Series

Reviews:

Related manuals for FX-iWP Series

Brands by name

Popular brands