A&D FX-iWP Series Page 65 Instruction Manual Download | Manualshive

Page: 65 / 79

background image

58

16. MAINTENANCE

In normal use, the balance can be cleaned with water. But, keep the following precautions so

that dust and water do not invade the balance.
  Do not direct water pressure at the bottom of the balance.
  Do not use powerful water jets.
  Do not immerse the balance in water.

Do not use organic solvents to clean the balance. Clean the balance with a lint free cloth that

is moistened with warm water and a mild detergent.

Do not disassemble the balance. Contact the local A&D dealer if the balance needs service or

repair.

Use the original packing material for transportation.

While cleaning the balance and keeping it waterproof, cover the RS-232C interface connector

using the terminal cover or connect the waterproof RS-232C cable (AX-KO2737-500), and
cover the AC adapter jack. Also, insure that the underhook cap is in place.

If water accumulates on the waterproof diaphragm, a weight value may be difficult to become

stable. Clean the diaphragm while taking much care not to deform it.

AC adapter jack
When the AC adapter is not connected,
cover the jack.

RS-232C interface
Cover the interface connector or connect the
waterproof RS-232C cable

«
...
63
64
65
66
67
...
»

Summary of Contents for FX-iWP Series
















































































Reviews:

No comments

Related manuals for FX-iWP Series

Brand: A&D Pages: 2

Brand: A&D Pages: 82

Brand: A&D Pages: 2

Brand: acaia Pages: 15

Brand: acaia Pages: 20

Brand: T Scale Pages: 49

PALLET RUNNER 3000

Brand: Salter Brecknell Pages: 20

Brand: Klarstein Pages: 21

Brand: Somogyi Pages: 7

Brand: White and Brown Pages: 6

Brand: U.S. Solid Pages: 38

Brand: Steinberg Pages: 7

Basic SBS-PS-180A

Brand: Steinberg Pages: 11

Brand: Bifinett Pages: 29

Micro-Touch 1500

Brand: Lyman Pages: 2

BrewMometer BMA-002F-04

Brand: Blichmann Engineering Pages: 5

Brand: MyWeigh Pages: 4

Brand: Beurer Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands