manualshive.com logo in svg

Aaeon SBC-410, Manual

Share
Download
Aaeon SBC-410 Manual Download Page 62

54    SBC-410 User's Manual

Onboard Serial Port2

This option enables serial port 2 on the motherboard and specifies

the base I/O port address for serial port 2. The settings are 

Auto

.

Disabled, 3F8h, 2F8h, 3E8h, 2E8h

. The Fail-Safe default setting is

Auto

.

Onboard Parallel Port

This option enables the parallel port on the motherboard and

specifies the parallel port base I/O port address.  The settings are

Auto,

 

disabled, 378, 278, 3BC

. The Fail-Safe default setting is

Auto.

Parallel Port Mode

This option specifies the parallel port mode. ECP and EPP are

both bidirectional data transfer sechemes that adhere to the IEEE

P1284 specification.  The settings are:

Setting

        Description

Normal

The normal parallel port mode is used.  This is the
default setting.

EPP

The parallel port can be used with devices that

adhere to the Enhanced Parallel Port (EPP) specifi-
cation.  EPP uses the exiting parallel port signals to
provide asymmetric bidirectional data transfer
driven by the host device.

ECP

The parallel port can be used with devices that

adhere to the Extended Capabilities Port (ECP)
specification.  ECP uses the DMA protocol to
achieve transfer rates of approximately 2.5 Mbs.
ECP provides symmetric bidirectional communla-
tions.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for SBC-410
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands