manualshive.com logo in svg

Aaeon SBC-410, Manual

Share
Download
Aaeon SBC-410 Manual Download Page 11

Chapter 1  General Information    3

Features

• Accepts any Intel, AMD, Cyrix, or other compatible processor

• Half-size ISA bus CPU card, fully 486SX/DX/DX2/DX4/5x86/Pentium

Over Drive compatible

• Built-in 128 KB secondary cache, up to 512 KB

• Up to 64 MB of on-board DRAM; supports 5V EDO DRAM

• Built-in IDE (AT bus) hard disk drive interface, floppy drive controller

• One RS-232 and one RS-232/422/485 selectable serial port; uses

16C550 UARTs with 16-byte FIFO

• One bi-directional parallel port

• 32 to 140

o

F (0 to 60

o

C) operating temperature

• Watchdog timer, software programmable from 2 to 32 seconds

(15 steps, 2 seconds per step)

• On-board keyboard connector and/or PS/2 mouse

• IDE HDD auto-detection

• Connectors for PC/104 module expansion

• 5V power supply

• "Green" function, supports power management

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for SBC-410
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands