background image

9

•  Turn off the ozone switch
•  Wait 10 seconds before continuing.       
•  Turn off the oxygen source.

Tube Connection and Start Up

An oxygen tank or oxygen generator can be used but is not required for ozone production.

Using Oxygen Bottle/Tank:

 

•  Connect oxygen bottle/tank to ozone generator (Oxygen In Port).
•  Connect MP-1000 Ozone Generator (Ozone Out Port) to venturi injector. 
•  Install a check valve 10 inches after ozone outlet tube fitting. This can be done by cutting a tube 

ten inches after ozone outlet fitting. 

•  Connect both ends of cut tubes to the check valve. Please direct the arrow on the check valve 

toward venturi injector.

•  Set tank gas flow meter at 1-3 liters per minute and 3 PSI maximum.
•  First, open the oxygen valve then only turn on the main ozone power switch on the front panel 

of the MP unit (internal air compressor switch stays OFF). The ozone light and fan should turn 
on. 

•  Increase power to the cells by turning the ozone concentration knob clockwise. Please remember 

to make a full rotation clockwise.

•  Prior to shutting off the feed gas to the unit, turn off the switch and allow the unit to purge for 

about 1 minute. 

•  Then, turn the flow of oxygen gas off.

NOTE:

 Do not turn the air pump switch ON when using oxygen generator, oxygen bottle or tank.

Using Oxygen Generator: 

•  Connect oxygen generator (Oxygen Out Port) to ozone generator (

O

2

 In Port).

•  Connect MP unit (Ozone Out Port) to the venturi injector.
•  Install a check valve 10 inches after ozone outlet tube fitting. This can be done by cutting a tube 

ten inches after ozone outlet fitting. 

•  Connect both ends of cut tubes to the check valve. 
•  Please direct the arrow on the check valve toward the venturi injector. 
•  Turn the oxygen generator ON first and then the ozone generator switches (the air pump stays 

OFF).

•  Turn timer knob clockwise to the amount of time needed.
•  The ozone light and fan should turn on. 
•  Increase power to the cells by turning the ozone control knob clockwise.

Summary of Contents for MP-1000


















Reviews: