background image

A2J GmbH · Am Fuchsberg 13 · 87452 Altusried · Tel. 0 83 73/98 72 69 · Fax 0 83 73/98 72 76 · E-mail [email protected] · Web www.a2j-intl.com

- 8 -

DOC 01042013 Technische Änderungen vorbehalten

Fig.6

Fig.7

HANDLEBAR HEIGHT

The steering unit may be adjusted in height to suit your individual
needs.

How to proceed:

Adjust the handlebar to the desired height (arrow Fig.6) using the

two screws (A Fig.6).

STAND

The stand helps you to quickly connect your Crazy Horse in the
same position (Fig. 7).

Adjust the stands

Introduce the long tube ends of the stands into the corresponding
locking rails from below (A, Fig. 7).

Tighten the Crazy Horse connection at the desired height on the
frame tube of the wheelchair.

Lift the caster wheels (see paragraph “LIFT”) and verify ground
clearance. It must be approx. 5 cm. If clearance is less than 5 cm,
contact your specialist dealer for turnbuckle adaptation.

Lower Crazy Horse (see paragraph “LOWER”).
Put the stand tubes on the ground in front of the corresponding

caster wheel.
Fix the stand tubes by tightening the corresponding clamps.

After being disconnected from the wheelchair, Crazy Horse now

rests on its stand in the right position to be re-mounted.

LIFTING

After you have mounted Crazy Horse to your wheelchair,
push the steering unit forward. – The caster wheels are lifted from

the ground and the turnbuckle lock clicks into place automatically.

LOWERING

Push the steering unit forward, pull the turnbuckle rope and
slowly lower the steering unit again.

A

Summary of Contents for Crazy Horse












Reviews: