background image

Page 8 

09/2021

Installation and Operating Instructions 
UPS Edition One 1kVA, 2kVA, 3kVA

1.7 Handling of batteries

■ 

  

When changing batteries, always insert the same number and type of 
batteries.

■ 

 

Batteries or their connections can cause electric shocks.

■ 

  

If short circuits occur on accumulators, touching the live parts can cause 
severe burns.

■ 

  

Batteries should never be brought into contact with heat sources or flames. 
Do not attempt to dispose of the batteries by burning them. 

 

There is a risk of explosion!

■ 

  

Do not open or destroy any batteries. The released electrolyte can cause 
injuries to the skin and eyes (caustic hazard). 

 

 

It is toxic and dangerous to humans and the environment.

■ 

  

Defective accumulators must be disposed of in an environmentally friendly 
manner.Do not throw them in the household waste under any circumstances 
and observe the local disposal regulations. 

 

 

Take advantage of the certified and professional recycling service of our 
AkkuSys team. For more information, contact us on the order hotline  

 

+49 4101/376760, at 

[email protected]

 or use the QR code.

Summary of Contents for UPS Edition One 1kVA

































Reviews: