A.O. Smith BFM - 100 Installation & Service Manual Download Page 36

Page: 36 / 74

Installation

Instruction manual BFM

3.11 Checking the supply

pressure and burner
pressure

Note

Before starting the appliance and/or checking the supply pressure and

burner pressure, you must fill

(5 "Filling")

the appliance.

Caution

Before starting up for the first time or after conversion, you must always

check the supply pressure and burner pressure.

Note

The easiest way to check the gas pressures is by using two pressure

gauges. This procedure assumes that these two gauges are available.

If the appliance is to be run on a different gas category than the factory preset
gas category (see type plate) then you must first convert

(4 "Conversion to a

different gas category")

the appliance.

Gas control for BFM 30 through 100

Legend

1. burner pressure regulator
2. burner pressure regulator cap
3. burner pressure regulator

adjustment screw

4. gas control connector
5. blank plate
6. supply pressure test nipple
7. gas control
8. manifold test nipple

IMD-0256 R1

Summary of Contents for BFM - 100











































































Search results

Summary of Contents for BFM - 100

Reviews:

Related manuals for BFM - 100

Brands by name

Popular brands

A.O. Smith BFM - 100, Installation & Service Manual

Search results

Summary of Contents for BFM - 100

Reviews:

Related manuals for BFM - 100

Brands by name

Popular brands