background image

2

SAFE INSTALLATION, USE, AND SERVICE

The proper installation, use and servicing of this water heater is extremely important to your safety and the safety of others.
Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you 

and others of a potential injury hazard.  Read and obey all safety messages and instructions throughout this manual.  It is very 

important that the meaning of each safety message is understood by you and others who install, use, or service this water heater.
This is the safety alert symbol.  It is used to alert you to potential personal injury hazards.  Obey all safety messages that follow 

testing, repair or servicing of appliances and equipment; that is experienced in such work; that is familiar with all precautions 

required; and that has complied with all the requirements of the authority having jurisdiction.”

DANGER

WARNING

CAUTION

CAUTION

DANGER indicates an imminently

hazardous situation which, if not avoided,

will result in injury or death.

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible

injury or death.

WARNING indicates a potentially hazardous

situation which, if not avoided, could result

in injury or death.

CAUTION indicates a potentially hazardous

situation which, if not avoided, could result in

minor or moderate injury.

CAUTION used without the safety alert

symbol indicates a potentially hazardous

situation which, if not avoided, could result in

property damage.

All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the safety 

message, and how to avoid the risk of injury.

IMPORTANT DEFINITIONS

• 

Qualified Installer or Service Agency:

Installation and service of this water heater requires ability equivalent to that of a Qualified Agency (as defined by ANSI 

below) in the field involved. Installation skills such as plumbing, electrical supply are required in addition to electrical testing 

skills when performing service.

• 

ANSI Z223.1 2006 Sec. 3.3.83: 

“Qualified Agency”  -  “Any  individual,  firm,  corporation  or  company  that  either  in  person  or  through  a  representative  is 

engaged in and is responsible for (a) the installation, testing or replacement of gas piping or (b) the connection, installation, 

testing, repair or servicing of appliances and equipment; that is experienced in such work; that is familiar with all precautions 

required; and that has complied with all the requirements of the authority having jurisdiction.”

Printed on 2/8/2018 9:05 AM CT

Summary of Contents for 52





















































Reviews: