background image

MIRACLE STEAMER

12

P/N 1010456 Rev. C 08/12

A.J. Antunes & Co.

NOTE:  If deposits are still excessive and/or diffi-

cult to remove, refer to Steps 6 and 11.

  6.  Pour delimer solution (not supplied) onto the 

Generator surface. Follow the delimer manufac-

turer’s instructions for proper mixture and use.

  7.  Using a sponge or a dry towel, remove the 

delimer solution from the Generator surface, then 

rinse with clean water.

Monthly

The Miracle Steamer utilizes an open steam generator.  

Water sprayed onto the Generator surface flashes into 

steam immediately, but the minerals in the water do not 

steam, they stay on the Generator surface.  

A small 

amount of calcium/mineral deposits are needed for 

proper operation

, but a buildup of excessive calcium/

mineral deposits causes poor steaming efficiency, 

excessive moisture (wet steam) and will eventually 

severely hinder the steaming action.

  1.  Turn the power off, unplug the power cord, and 

allow the unit to cool down.

  2.  Perform the Daily cleaning, but do NOT reas

-

semble the unit.

  3.  Remove the Wing Nut, Generator Cover, and 

Diffuser (Figure 8).  Wash these items in hot, 

soapy water, rinse and 

WIPE DRY

.

  4.  With the unit cool, use a wire brush and/or  

scraper to loosen and remove the excessive  

calcium/mineral deposits from the Generator  

surface (Figure 8).  

  5.  Take a wire brush and clean out any buildup from 

the 28 Steam Ports (26 vertical and 2 horizontal) 

of the Generator (Figure 8). Remove the loose 

buildup, wipe the Generator with a clean, damp 

cloth, and reassemble the unit.

CAUTION

If a chemical cleaner/delimer is used, be sure it is 

safe to use on cast aluminum.  Observe all pre-

cautions and warnings on the product label.

MAINTENANCE (continued)

NOTE: To ensure proper steaming characteristics, 

some calcium/mineral deposits must be present on 

the Generator surface.  If, during cleaning, the sur-

face does become free of calcium/mineral deposits, 

add plain tap water to the surface and allow it to 

boil off.  If necessary, repeat this process to formu-

late a thin coating of calcium/mineral deposits.

NOTE: In soft water areas, it may be necessary 

to add a small amount of lime to the Generator to 

“season” it. This will ensure proper steaming char-

acteristics by producing a thin coating of calcium/

mineral deposits on the Generator surface. 

Seasoning mixture consists of 3/4 ounces (25ml/ 

25cc) baking soda, 3/4 ounces (25ml/25cc) lime 

mixed with 1 quart (950ml/950cc) of water.  Stir 

mixture and pour 1/4” deep onto the hot Generator 

surface.  After mixture is converted to steam, the 

remaining loose power can be removed.

  8.  Plug the power cord into the appropriate outlet.

  9.  Turn the power on and allow the unit to warm up 

for approximately 30 minutes.

 10.  Push and release the 

OPERATE

 button or the 

START/STOP 

button several times to operate the 

steamer.  

This purges any remaining delimer 

residue from the Generator surface.

  11.  Turn the power off, reinstall all parts and accesso-

ries, and return the unit to service.

READY

ADD

WATER

Diffuser

Wing Nut

Generator 

Cover

 

Generator

Steam Ports 

(26 vertical and 

2 horizontal)

Figure 8. Monthly Cleaning

Summary of Contents for roundup MS-355





















Reviews: