background image

A.H. Systems SAS-510-2 Log Periodic Antenna

INTRODUCTION

The SAS-510-2 Log Periodic Antenna (also known as a log periodic dipole array) is a 
compact,   lightweight   antenna   that   has   been   designed   to   ensure   maximum   gain,   low 
VSWR and high power handling capabilities. This compact design is an ideal solution for 
EMC testing where the reduced size of the antenna is preferred to minimize chamber wall 
coupling and increasing the half power beamwidth to a more acceptable angle that will 
cover the whole device under test. Constructed of lightweight aluminum, the SAS-510-2 
Log Periodic Antenna has been manufactured to operate over a very wide bandwidth. 
Weighing in at just 1.5 pounds this Log Periodic Antenna is one of the lightest antennas 
commercially available.

The SAS-510-2 Log Periodic Antenna is the standard workhorse of any EMC compliance 
test house. The SAS-510-2 has an excellent Front to back ratio and cross-polarization 
properties that is required per CISPR 16-1 that greatly reduces measurement uncertainty. 
This Linearly polarized antenna is an ideal solution for radiated emissions and normalized 
site attenuation. 

 A.H. Systems inc. – January 2007

REV B

3

Summary of Contents for SAS-510-2















Reviews: