background image

11

Fitting and removing the battery pack

To remove the battery pack 

from the blower firmly press the 

battery release tabs (4) at either 

side of the battery pack, and slide 

the battery backward out of the 

tool.
To install the battery pack, align 

 rails, on the tool with the tabs 

on the battery pack and slide the 

battery pack on to the blower. Ensure the battery pack is 

sitting straight on the foot and correctly entering the runners. 

The battery should slide fully on to the drill foot until the 

battery pack “clicks” into position.

Battery charging 

•  

The battery supplied with this 

tool is model number 2G18LB.

•  

The Charger Pack supplied 

with this tool is model number 

2G1835LC.

•  

The Charger Adaptor supplied 

with this tool is model number 

2G1835LA.

Note.

 Only use the supplied 

batteries, charger and adaptor.

IMPORTANT.

 Before plugging 

in the power supply from the 

charger to the slim line adaptor 

always ensure that the plug is 

switched off at the mains. 

IMPORTANT.

 The battery will be 

fully charged after approximately 

3–5 hours, remove it from the adaptor after this time.  

Do not leave a battery charging for longer than 24 hours. 

1. Align and slide the slim line 

adaptor onto the battery 

until the battery pack latches 

“click” into position. Check 

the adaptor is flush with the 

battery and there is a firm 

connection. 

2. Connect the power supply 

from the charger (5) to the slim 

line adaptor via the socket in 

the rear of the adaptor housing. 

3. Plug in the charger and switch 

on. The red LED indicator will 

show power to the adaptor and 

that charging is taking place. 

4. The battery charging time is 

approximately 3 - 5 hours to 

charge a low charged battery, but will be shorter if the 

battery is already partially charged. The red LED goes 

out when the charging cycle is complete. Turn off the 

charger power supply from the mains and then remove 

the battery from the adaptor. 

WARNING.

 Only use charger model 2G1835LC with the 

adaptor model 2G1835LA) that is supplied for the model 

2G18LB battery pack.

To obtain the best life for the battery 

For battery storage and when the blower is not being used, 

it is advised to charge the battery to approximately half 

charge. Leaving the battery in the fully charged condition 

can shorten the cell life.
Short charging is acceptable with these cells.  
Prevent constant overloading of the blower. 
Avoid allowing lose items like screws or nails etc. to be 

stored with battery packs as these or similar items can  

short battery packs and cause a fire or explosion.
Always unplug the charger when not in use and store in  

a dry secure place. 

Summary of Contents for BL18L














Reviews: