4xem IPVS1A User Manual Download Page 48

Page: 48 / 103

Any change made to this page will make the system restart to validate. Make sure every field is

correctly typed before clicking on

To eliminate incautious mistakes during installation, Video Server will stay in installation mode

whenever it starts unless "

Reset network at next boot

" is disabled. This option can also be

disabled using the Installer program. Once the option is disabled, Video Server will skip

installation at the next boot and the Installer program will not find the installed units. That

implies that Video Server cannot be accessed if no one remembers the IP address, except by

restoring factory default settings. However, with this option disabled Video Server can

automatically operate normally after restarting in case of losing power. This option is ignored in

the PPP connection.

Administrators may modify the network settings to fit into existing networks. Some broadband

service subnet mask may differ from the default value 255.255.255.0 and service providers may

assign some specific network settings. Administrators should change the configuration according

to what is given by the service provider. The configuration may include "

IP address

", "

Subnet

Mask

", "

Default Router

", "

Primary DNS

" and "

Secondary DNS

". After changing network

settings, be sure to leave "

Reset network at next boot

" blank to skip installation when the

system restarts. Otherwise the settings will be erased.

Video Server not only plays the role of server, it will also actively connect to servers outside to

send out messages or snapshots. When Video Server starts, it will send out a system log to notify

administrators. Even in modem application, Video Server will send out a connection log

whenever it dials out to an ISP or dialup server outside. If the administrator has setup some

applications in either event mode or sequential mode, Video Server will send out snapshots once

conditions are met. There are two methods to send files, including e-mail and FTP. To ensure

Video Server sends out files correctly, administrators should set valid "

SMTP (mail) server

" and

Recipient email address

" as well as "

Primary FTP Server

", "

Primary FTP user name

" and

Primary FTP password

". “

Return email address

” is whom the mail will return when the

Summary of Contents for IPVS1A








































































































Search results

Summary of Contents for IPVS1A

Reviews:

Related manuals for IPVS1A

Brands by name

Popular brands

4xem IPVS1A, User Manual

Search results

Summary of Contents for IPVS1A

Reviews:

Related manuals for IPVS1A

Brands by name

Popular brands