background image

Quick Installation Guide 

HSG320 Wireless Hotspot Gateway ENGLISH 

 

Copyright © 4IPNET, INC. All rights reserved.   

iii

CE CAUTION 

 

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for   

European Community, Switzerland, Norway, Iceland, and Liechtenstein   

Model: HSG320   

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence 

fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement. 

• Radio: EN 300.328

:

 

• EMC: EN 301.489-1, EN 301.489-17,   

• EMC: EN 55022

 

Class B, EN 55024

:

+ A1 + A2

 

including the followings: 

   EN 61000-3-2, EN 61000-3-3. 

      EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,   

      EN 61000-4-5, EN 61000-4-6, EN 61000-4-11 

• Safety: EN 60950-1 + A11, 

 

Caution:

   

 

This declaration is only valid for configurations (combinations of software, firmware, and hardware) 

provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported 

by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory 

requirements.  

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 

2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may 

be restricted to certain frequencies and/or may require a license for operation. Contact your local 

regulatory authority for compliance. 

 

Taiwan NCC Statement

 

 

 

根據

NCC

低功率電波輻射性電機管理辦法

 

規定

:

 

第十二條

 

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

 

第十四條

 

 

 

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時應立即停用,並改善至

無干擾時方得繼續使用。

 

前項合法通信,指依電信法規定作業之無線電通信。

 

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。

 

Summary of Contents for HSG320





















Reviews: