background image

PAGE 11

1. EXCLUSIVE WRITTEN LIMITED WARRANTY

ALL PRODUCTS SOLD ARE WARRANTED BY THE COMPANY (4B COMPONENTS 

LIMITED, (4B) BRAIME ELEVATOR COMPONENTS LIMITED, AND (4B) S.E.T.E.M. Sarl 

HEREIN AFTER REFERRED TO AS 4B TO THE ORIGINAL PURCHASER AGAINST 

DEFECTS IN WORKMANSHIP OR MATERIALS UNDER NORMAL USE FOR ONE (1) 

YEAR AFTER DATE OF PURCHASE FROM 4B.  ANY PRODUCT DETERMINED BY 

4B AT ITS SOLE DISCRETION TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP 

AND RETURNED TO A 4B BRANCH OR AUTHORIZED SERVICE LOCATION, AS 4B 

DESIGNATES, SHIPPING COSTS PREPAID, WILL BE, AS THE EXCLUSIVE REMEDY, 

REPAIRED OR REPLACED AT 4B’S OPTION.

2. DISCLAIMER OF IMPLIED WARRANTY

NO WARRANTY OR AFFIRMATION OF FACT, EXPRESSED OR IMPLIED, OTHER 

THAN AS SET FORTH IN THE EXCLUSIVE WRITTEN LIMITED WARRANTY 

STATEMENT ABOVE IS MADE OR AUTHORIZED BY 4B.  4B SPECIFICALLY 

DISCLAIMS ANY LIABILITY FOR PRODUCT DEFECT CLAIMS THAT ARE DUE TO 

PRODUCT MISUSE, ABUSE OR MISAPPLICATIONS, AS AUTHORIZED BY LAW, 

4B SPECIFICALLY DISCLAIMS ALL WARRANTIES THAT THE PRODUCT IS FIT OR 

MERCHANTABLE FOR A PARTICULAR PURPOSE.

3. NO WARRANTY “BY SAMPLE OR EXAMPLE”

ALTHOUGH 4B HAS USED REASONABLE EFFORTS TO ACCURATELY ILLUSTRATE 

AND DESCRIBE THE PRODUCTS IN ITS CATALOGS, LITERATURE, AND WEBSITES, 

SUCH ILLUSTRATIONS AND DESCRIPTIONS ARE FOR THE SOLE PURPOSE OF 

PRODUCT IDENTIFICATION AND DO NOT EXPRESS OR IMPLY A WARRANTY 

AFFIRMATION OF FACT, OF ANY KIND OR A WARRANTY OR AFFIRMATION 

OF FACT THAT THE PRODUCTS WILL CONFORM TO THEIR RESPECTIVE 

ILLUSTRATIONS OR DESCRIPTIONS.  4B EXPRESSLY DISCLAIMS ANY WARRANTY 

OR AFFIRMATION OF FACT, EXPRESSED OR IMPLIED, OTHER THAN AS 

SET FORTH IN THE EXCLUSIVE WRITTEN LIMITED WARRANTY STATEMENT 

ABOVE, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

4. LIMITATION OF DAMAGES

ANY LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL, EXEMPLARY, OR 

PUNITIVE DAMAGES, OR FOR LOSS OF PROFIT WHETHER DIRECT OR INDIRECT, 

IS EXPRESSLY DISCLAIMED.

PRODUCT WARRANTY

Summary of Contents for Binswitch Elite BSE1V10C













Reviews: