– 26 –
– 27 –
ENG
•
Turn on: Turn the key on the right side of the battery clockwise to the ON
position. It will do a system check: don’t start using your HAND-BIKE
BATEC ELECTRIC until it has finished with the system check and all the
lights are on.
(See fig. 27)
•
Turn off: Turn the key on the battery anti-clockwise to the OFF po-sition.
If you leave it in the OPEN position, your HANDBIKE BATEC ELECTRIC
will be off and the battery will be ready to remove.
(See fig. 27)
•
Speed up: Pull the HANDBIKE BATEC ELECTRIC QUAD MINI handle-bar
towards you to activate the throttle.
(See fig. 28)
•
Brake: Push the HANDBIKE BATEC ELECTRIC QUAD MINI handlebar away
from you to activate the brake.
(See fig. 29)
•
Moving forwards and backwards and limiting speed
(See fig. 30)
:
–
Press the F button to move forwards.
–
Press it again to select the 3 speed limits, successively.
–
Press the R button to move backwards.
–
This is only possible if the HANDBIKE BATEC ELECTRIC is stopped and
the throttle not engaged.
•
Lights: There is a button on the HANDBIKE BATEC ELECTRIC handle-bar to
switch on the front and rear lights. When you push the but-ton, the front
light will go on in normal mode and the light indicator on the display
panel will turn green. When you push the front light button again, it
changes to high-beam mode, and so on. To turn off the lights, hold the
button down for 2 seconds. The front light is below the battery and the
two rear lights, on either side of the stand frame.
(See fig. 31a, 31b, 31c)
4.8. OPERATING THE HANDBIKE BATEC ELECTRIC MINI 2 / MINI /
ELECTRIC 2 (RAPID 2) / SCRAMBLER HEMI CONTROLS
•
You can find out the meaning of all the symbols used on the controls of the
BATEC ELECTRIC HANDBIKE in Figure 58.
•
Turn on: Turn the key on the right side of the battery clockwise to the ON
position. It will do a system check: don’t start using your HAND-BIKE
BATEC ELECTRIC until it has finished with the system check and all the
lights are on.
(See fig. 32)
•
Turn off: Turn the key on the battery anti-clockwise to the OFF posi-tion.
If you leave it in the OPEN position, your HANDBIKE BATEC ELEC-TRIC will be
off and the battery will be ready to remove.
(See fig. 32)
•
Speed up: The throttle is on the right or left grip on the handlebar.
(See fig.
33)
•
Brake: Pressing on the brake lever and the red lever at the same time blocks
the brake lever, acting as a parking brake.
(See fig. 34)
•
Moving forwards and backwards and limiting speed:
(See fig. 35)
:
–
Press the F button to move forwards.
–
Press it again to select the 3 speed limits, successively.
–
Press the R button to move backwards.
–
This is only possible if the HANDBIKE BATEC ELECTRIC is stopped and
the throttle not engaged.
•
Lights: There is a button on the HANDBIKE BATEC ELECTRIC handlebar to
switch on the front and rear lights. When you push the button, the front
light will go on in normal mode and the light indicator on the dis-play panel
will turn green. When you push the front light button again, it changes to
high-beam mode, and so on. To turn off the lights, hold the button down
for 2 seconds. The front light is below the battery and the two rear lights, on
either side of the stand frame.
(See fig. 36a, 36b, 36c)
4.9. BATTERY
BATEC MOBILITY offers 2 36-V lithium-ion batteries: 280 Wh and 522 Wh,
respectively and 1 48 V 679 Wh lithium-ion battery. Each without memory
effect and with a cable-free connection system.
THE 280 WH BATTERY COMPLIES WITH IATA-DGR REGULATIONS for air travel
with batteries in mobility-aid devices.
(See fig. 37)
Summary of Contents for BATEC ELECTRIC 2
Page 27: ...52 FIG FIGURES...
Page 32: ...14a 16a 14b 16b 15 17 FIG...
Page 39: ...44 46 48 50 49 45 47 FIG...
Page 41: ...59 7 1 2 3 4 5 6 NUM 7 100 6 90 5 80 4 60 3 40 2 20 1 8 1...
