background image

7

INSTALLATION RADIO SHUTTER MOTOR

Installation situation

1

 Counter bearing

*

  

2

 Ball bearing

*

   

3

 Roller capsule

*

4

 Shutter shaft

*

 

 

 

5

 Suspension spring

*

   

6

 Shaft adapter

   

7

 Tubular motor   

8

 Limit switch adapter

   

10

 Limit switches

10

 Engine mount

11

 Shutter curtain

*

Accessories; not included

1

 Prepare power connection:

 The mains connection cable of the drive must be laid internally in the empty conduit up to the junction box. 

  The local electrical regulations must be observed.

1 2

3

4

5

6

7

8 9 10

11

Please note:

 The motor can be installed on the right-hand side as well as on the left-hand side. 

  If the direction of rotation is reversed, please exchange the wires for the up and down direction.

 The setting of the end positions is only possible in the installed state (motor in shutter shaft).

 Never place screws in the area of the tube motor, as they will damage the motor.

 

Engine damage caused by improper use or unprofessional installation, 

  lead directly to loss of warranty.

 INSTALLATION INSTRUCTIONS

3T-MOTORS Radio tubular motors

  |  Installation instructions

Summary of Contents for 3T-MOTORS 3T45-20RNH





















Reviews: