3M VF-45 Page 4 Instructions Manual Download

Page: 4 / 32

3.0 3M

™

VF-45

™

Socket

3.1

Contains the following:

a) Housing

c) Boot

b) Socket fiber holder (SFH)

d) Base

Note: The VF-45 Socket is sold separately.

4.0 Installation

4.1

Position polishing base.

At the patch panel area, place the polishing base on the

patch panel work tray or on a nearby suitable surface. At

the work area outlet, choose a suitable surface. Open the

hinged scribe cover.

Attach a sheet of lapping film to polishing surface of the

station. Removal of the release liner from lapping film

exposes adhesive backing to secure the lapping film to the

polishing surface.

Tech Tip: Before placement of the lapping film, clean the

polishing surface with a lint free wipe moistened

with isopropyl alcohol. Lapping film will last for

about 50 connectors.

Tech Tip: All Isopropyl Alcohol should be reagent grade, 99%

or better. The use of inferior alcohol will adversely

effect interconnect losses. This can be purchased

from a chemical supply house.

Summary of Contents for VF-45

































Search results

Summary of Contents for VF-45

Reviews:

Related manuals for VF-45

Brands by name

Popular brands

3M VF-45, Instructions Manual

Search results

Summary of Contents for VF-45

Reviews:

Related manuals for VF-45

Brands by name

Popular brands