4
ON ~ 3 sec
~ 2 sec
OFF
3. The TEP-300 and/or the ComTac™ VII will indicate
pairing.
• 2 short beeps, indicates a successful pairing to the
SCU-300.
• 3 long beeps, indicates the NFMI link is lost.
•
Beep Beep
Beeeep Beeeep Beeeep
Note:
Beeping sounds only occur if the headset has
previously been paired with the SCU.
4. If pairing fails, check proper SCU placement. If problem
persists, press the On/Off/Menu button on the SCU-300
for ~10 seconds or until 2 short beeps are heard in
TEP-300 and/or the ComTac™ VII.
6.3. TO POWER ON THE SCU AND CONNECT
THE TEP-300 AND/OR THE COMTAC™ VII FOR
THE FIRST TIME
This product uses Near Field Magnetic Induction (NFMI),
to connect wirelessly to the TEP-300 and/or ComTac™
VII. NFMI is a short range wireless physical layer that
communicates by coupling a tight, low-power,
non-propagating magnetic field between devices. The
range is ≈ 50 cm/20 in. NFMI systems are designed to
contain transmission energy within the localized magnetic
field and the energy does not radiate into free space.
If not previously connected to the SCU-300, the TEP-300
and/or ComTac™ VII must be paired manually.
1. Power on the TEP-300 and/or the ComTac™ VII.
2. Press and hold the On/Off/Menu button on the
SCU-300 for a minimum of ~10 seconds.
~ 10 sec
• 2 short beeping sounds indicate that the hearing
protection is connected to the SCU-300.
• 3 long beeping sounds indicate that the NFMI link
is lost. Press and hold the On/Off/Menu button for a
minimum of 10 seconds to reconnect the hearing
protection.
Beep Beep
Beeeep Beeeep Beeeep
6.4. TO POWER ON THE RCU-300
1. Short press the + button to start the RCU.
ON
2. Press any button to wake up the RCU if it has gone into
sleep mode.
6.5. TO POWER OFF THE PRODUCT
6.5.1. TO POWER OFF THE SCU-300
1. Press and hold the On/Off/Menu button on the SCU-300
for ~2 seconds.
ON ~ 3 sec
~ 2 sec
OFF
NOTE:
If the connection between the SCU-300 and the
TEP-300 and/or the ComTac™ VII is lost, the user will hear
three long beeps.
6.5.2. TO POWER OFF THE RCU-300
1. Press and hold the + and - button at the same time for 2
seconds.
OFF
~ 2 sec
Note:
The RCU-300 will go into sleep mode after 120 minutes
after lost connection with SCU-300. There is no need to
manually power off the RCU-300.
6.6. TO PAIR THE RCU-300 TO THE SCU-300
RCU-300 uses Bluetooth
®
Low Energy (BLE) communication.
BLE is a short-range wireless communication protocol. It is
designed for long battery life.
The range is ≈ 50 cm/20 in.
Pairing the RCU-300 to the SCU-300 requires the use of the
TEP-300 or ComTac™ VII headset. Refer to those product
user instructions for use information.
1. Power on the SCU-300. Refer to “6.2. To power on the
SCU-300”.
2. Power on the RCU-300. Refer to “6.4. To power on the
RCU-300”.
3. Short press the power button on the SCU-300 to access
the menu.
~ 0.5 sec
4. Short press the - button to move forward in the menu
system until the audio message indicates the “Advanced
Settings” sub menu.
5. Select “Advance Settings” by short pressing the + button.
6.
Radio
Volume
Ambient
Listening
Advanced
Settings
Short press the - button to move forward in the sub-menu
system until the audio message indicates “Primary RCU
pairing”.
7. Select “Primary RCU pairing” with the + button.
8. Press and hold the PTT II and - button on the
same time on the RCU-300.
EN
