manualshive.com logo in svg

3M MicroTouch Display C1700SS, Installation Manual

Share
Download
3M MicroTouch Display C1700SS Installation Manual Download Page 13

3M™ MicroTouch™ Display C1700SS Installation Guide 

13 

 

3M Touch Systems Proprietary Information

 

Access to the Video Controls 

The controls for adjusting the video display are located on the back of the C1700SS 
Display.  These buttons let you display the on-screen menu and adjust the phase, image 
position, contrast, and brightness.  Make sure you will be able to access the video 
controls once the C1700SS Display is installed. 

Clearance and Ventilation 

Leave at least two inches of clearance space behind the C1700SS Display for proper 
ventilation. Units have vent holes at the top and bottom on the back of the chassis -- 
ensure these holes are not blocked during installation.  Always maintain adequate 
ventilation to protect the display from overheating and to ensure reliable and continued 
operation. Refer to the published specifications for the maximum and minimum operating 
temperature and humidity conditions. 

Securing and Routing System Cables 

You must be sure to secure all cable connections.  Shaking and vibration, especially 
during shipment, may dislodge components that are improperly connected. 

•

 

Be sure to tighten all cable screws. 

•

 

Route all wiring and cabling away from heat sources and sharp metal edges to avoid 
damage.  Also, keep the touch sensor cable away from sources of electromagnetic and 
radio frequency interference. 

Installing the Video Card and Video Driver 

Before you can connect your touch display, make sure your computer has a video card 
already installed for the display.  After you connect the display, you need to install the 
video software driver.  The video driver is supplied by the video card manufacturer and 
may be found on the diskettes that came with your computer. If you need information on 
installing a video card or video driver, refer to the manual that came with your video 
card. 

Supported Video Display Modes and Refresh Rates 

Your video card must support one of the display modes specified in Table 1.  If you 
select an unsupported video mode, the display will stop working or display an 
unsatisfactory picture quality. 

Summary of Contents for MicroTouch Display C1700SS

























Reviews:

No comments

Brands by name

Popular brands

Load more brands