background image

 
 

 

3M © 2003  78-8078-8977-5                    Page 3 of 9                                           Attest 290 Auto-reader 

 SAFETY INFORMATION 

 

Power Supply Specifications   

 

Power supply 

Operating Condition 

Units 

Voltage Range 

100-240 

Volts AC 

Frequency 50/60 

Hertz 

Current 1.2 

Amps 

 

Environmental Operating Conditions   

 

Environmental Condition 

Operating Condition 

Units 

Altitude 2500 

(max) 

meters 

Operating Temperature 

16-43 

°

C  

 

Relative Humidity 

20-80 (non-condensing) 

Voltage Range 

12 

Volts DC 

Frequency DC 
Current 2.4 

Amps 

Installation/Over Voltage 

Category II 

Pollution Degree 

 

Health and Safety Information  

 

Device Safety Compliance 

The Attest 290 Auto-reader complies with the 
standard IEC/EN 61010-1 as demonstrated by the 
CB Scheme Certificate and test report that 
Underwriters Laboratories Inc. (UL) generated. 
 
The Attest 290 Auto-reader is listed as Laboratory 
equipment and carries the UL and c-UL marks 
based on compliance to the standards UL 3101-1 
and CSA 22.2 No. 1010-1.92. 
 
The Attest 290 Auto-reader complies with the CE 
mark related to the Low Voltage Directive 
73/23/EEC as confirmed in the Declaration of 
Conformity. 
 

EMC Compliance  

The Attest 290 Auto-reader complies with IEC/EN 
61326-1 as confirmed in the Certificate of 
Compliance generated by 3M. 
 
The Attest 290 Auto-reader complies with the EMC 
requirements of the CE mark EMC Directive 
89/336/EEC. 
 
The Attest 290 Auto-reader complies with the 
Australian EMC requirements as confirmed in the 
Supplier’s Declaration of Conformity that is linked 
to the C-tick mark. 

Note:

 This equipment has been tested and found to 

comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide a reasonable protection 
against harmful interference when the equipment  
is operated in a commercial environment. This 
equipment generates, and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause 
harmful interference to radio communications. 
Operation of this equipment in a residential area  
is likely to cause harmful interference in which case 
the user will be required to correct the interference  
at their own expense. 
 
This Class A digital apparatus meets all 
requirements of the Canadian Interference-Causing 
Equipment Regulations. 

 

Cet appareil numerique de la classe A respecte 
toutes les exigences due Reglement sur le materiel 
brouilleur du Canada. 

 
 
 

Summary of Contents for Attest 290













Reviews: