background image

 
 

 

3M © 2003  78-8078-8977-5                           Page 4 of 9 

Attest 290 Auto-reader 

  INSTRUCTIONS FOR USE 

 

Operating Instructions 

 

Start-up 

 
Place unit on a firm level surface. Plug unit into an 
appropriate AC grounded outlet.  
 
Allow a 30 minute warm-up period before placing 
RRBIs into the incubation wells. The C1 caution 
code will disappear when proper incubation 
temperature is reached. 
 

It is recommended that the unit be left on to 
eliminate warm-up periods

. The unit may be 

turned off when it is anticipated that it will not be 
used for an extended period. 
 
 

Readout Procedure 

 
Follow this procedure for every RRBI to be read: 
 

 

 

 

Step 1

. While wearing gloves and 

safety glasses, 

CLOSE

 RRBI cap 

by pressing down. 

 

 

Step 2

CRUSH

 the glass ampule 

(containing growth media) in the 
designated crushing well built 
into the incubator. 

 

 

Step 3

. Hold the RRBI by the cap 

and 

TAP

 bottom of the vial on a 

tabletop until media wets spore 
strip at bottom of vial.  Do not tap 
vial on unit. 
 

 
 

 

 

Step 4.

 Open the cover and 

PLACE

 the RRBI into an 

incubation/reader well. 

 

Step 5.

 

CLOSE

 the cover on the 

Attest 290 Auto-reader and wait 
for either the red or green 
indicator light to signal the result.
 

 

 

 
 
 

 

  

WARNING

WARNING

WARNING

WARNING

 

 
Do not remove or change 
placement of RRBI once it 
is placed into a well. Doing 
so may result in loss of 
results and the RRBI test 
may be invalid. 

Summary of Contents for Attest 290













Reviews: