background image

Equipment Warranty and Limited Remedy:  THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OF IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR
USAGE OF TRADE:

3M sells its AccuGlide™ 

II

 STD 1-1/2 Inch Lower Taping Head, Type 29600  with the following warranties:

1.

The Taping Head knife, springs, and rollers will be free from all defects for ninety (90) days after
delivery.

2.

All other Taping Head parts will be free from all defects for three (3) years after delivery.

If any part is proved to be defective within its warranty period, then the exclusive remedy and 3M’s and seller’s
sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned
immediately to 3M’s factory or an authorized service station designated by 3M.  A part will be presumed to have
become defective after the warranty period unless the part is received or 3M is notified of the problem no later
than five (5) calendar days after the warranty period.  If 3M is unable to repair or replace the part within a
reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price.  3M shall have no
obligation to provide or pay for the labor required to install the repaired or replacement part.  3M shall have no
obligation to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any
accidental cause other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning,
improper operating environment, improper utilities, or operator error.

Limitation of Liability:  3M and seller shall not be liable for direct, indirect, special, incidental or consequential
damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.

The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a
written agreement signed by authorized officers of 3M and seller.

ii

AccuGlide™, Scotch™, and 3M-Matic™ are Trademarks of 3M, St. Paul, Minnesota 55144-1000

Taping Head Contents

Qty.

Part Name

 1

Taping Head Assembly

 1

Tape Drum and Bracket Assembly

 1

Hardware and Spare Parts Kit

 1

Threading Tool

Summary of Contents for AccuGlide II 29600





































Reviews: