3D Systems ProX 950 User Manual Download Page 14

Page: 14 / 62

3D Systems, Inc.

Emergency Stop:

This switch is located on side panel

above the touch screen. Emergency Stop immediately

disables all motion controls and Lasers and renders them

safe. After being pressed, it remains in the closed state

until it is manually returned to the open state.

Touchscreen:

Displays the Print3D Pro software which is

used to operate the system.

Buttons, Indicators, USB Ports
LED Indicators:

The LED indicators indicate the readiness

of the machine and its Lasers.

• “

Laser

” Blue LED

, Solid

» Printhead enabled

OFF

» Printhead disabled or off.

• “

Control

” Green LED

- ON

, Solid

» Control systems are enabled. The machine is

ready for use.

- ON

, Flashing

» Machine is in BYPASS mode.

- OFF

» Control systems are not enabled. The machine is

not ready for use.

• “

System

” Amber LED

- ON

, Solid

» All safety and interlock systems have been

satisfied. Laser safety shutter is operational.

- OFF

» All safety and interlock systems have not been

satisfied. Laser safety shutter is not operational.

System Enable

Once the software has been launched,

user will press the System Enable button to lock the doors

so system is ready to print a build. Use System Enable

after someone has pushed the emergency stop, when the

emergency has been cleared and user wants to resume

building.

USB:

Three standard auxiliary USB ports connected to the

control PC are be located under User Interface

Chamber Lights

This switch turns the chamber lighting

on or off.

Note: The chamber lights can be repositioned to view

specific areas as needed. Check the switch on the lights

themselves if they do not come on when you press the

button under the user interface .

B
C

SYSTEM COMPONENTS

For system requirements, consult the

Facility Requirements Guide

User Interface

The User Interface consists of a touchscreen located on the side

of the printer and the system status LED indicators. An E-Stop is

located above the touchscreen. See the section,

Software Overview

on page 18

for descriptions of the touchscreen functionality.

Summary of Contents for ProX 950






























































Search results

Summary of Contents for ProX 950

Reviews:

3D Systems ProX 950, User Manual, Page: 14 / 62

Search results

Summary of Contents for ProX 950

Reviews: