3D Histech TMA Grand Master 2.0 User Manual Download Page 15

Page: 15 / 72

TMA Grand Master 2.0 – User’s Guide

3 Installation of TMA Grand Master

Software Application

3 Installation of TMA Grand Master Software Application

3.1 Prerequisites for the TMA Grand Master Software

Application Installation

Prerequisites

Description

Hardware

Recommended

Intel Pentium DualCore, 3.2 GHz, 4GB RAM

Monitor Screen resolution

Recommended:

UXGA (1680×1050 or 1920×1080 True Color) or better at 96 Dpi

Operating system

Microsoft Windows 7 Professional 64-bit SP1 EN

Disk space

Recommended:

3GB – for application software, drivers, prerequisite and temporary files
500 GB – if HDD is used for storing slides
1-1TB – for saving database

3.2 TMA Grand Master Software Installation

Important!

3DHISTECH service technicians perform the installation and configuration of the

TMA

Grand Master

software application.

The following installation procedure is for information purposes only – follow the

below steps only if you need to re-install the software, or upgrade to a newer
software version.

Important!

Do NOT install any other application than the

TMA Grand Master

software

application and its auxiliary drivers on the control computer.

If the application is running, make sure there is no high traffic communication over

USB ports used by other devices.

November 5, 2013 – Rev. 1

3DHISTECH Ltd.

15(72)

Summary of Contents for TMA Grand Master 2.0









































































Search results

Summary of Contents for TMA Grand Master 2.0

Reviews:

3D Histech TMA Grand Master 2.0, User Manual, Page: 15 / 72

Search results

Summary of Contents for TMA Grand Master 2.0

Reviews: