manualshive.com logo in svg

3Com OfficeConnect 3C892A, User Manual, Page: 99 / 130

Share
Download
3Com OfficeConnect 3C892A User Manual Download Page 99

Monitoring LEDs

93

Troubleshooting

Problems Indicated by

LEDs

Table Table 8 lists the states of ISDN LAN Modem LEDs which indicate errors and 
also provides possible causes and solutions.

Table 8   

Troubleshooting Problems Indicated by LEDs

LED 

LED State

Possible Cause

Solution

ALERT LED

ALERT LED remains 
lit.

An internal failure.

Notify your reseller or technical support that the ISDN 
LAN Modem has failed the self-test.

ALERT LED continues 
to flash.

Self test failure or ISDN LAN 
Modem is in firmware download 
mode.

Power cycle the ISDN LAN Modem. If the ALERT LED 
continues to flash, the ISDN LAN Modem has failed the 
self test. Contact your network supplier. If the ALERT 
LED is not flashing, then the ISDN LAN Modem is now 
operating correctly.

Upon power up, both 
the ALERT and ISDN 
LEDs flash.

A previous firmware download 
was not completed successfully.

Download the firmware. Refer to the Readme file 
located at 

http://www.remoteaccess.3com.com/support/do
cs/lanmodem

 for firmware download instructions.

ALERT, ISDN OK, B1, 
and B2 LEDs 
alternately flash.

Firmware download process was 
aborted.

Do not remove power plug. 

Wait until the LEDs stop 

flashing (about 1 minute) to allow the ISDN LAN modem 
to cancel the firmware download. Once the LEDs stop 
flashing, you may restart firmware download.

B1/B2

B channel LED(s) do 
not remain green or 
amber.

Problem with your computer or 
application software or 
incompatible local or toll 
telephone company.

Carefully monitor the B1 and B2 LEDs while attempting 
a call. These LEDs flash during call establishment and 
then remain green or amber once the connection is 
established. 

If neither LED flashes, make sure that your computer is 
turned on and operational. 

If you are able to place a voice call but not a data call, 
then there may be an incompatible local or toll 
telephone company. Contact your local telephone 
company and have it verify that you can dial a data call 
to the destination telephone number.

ISDN LED

 

ISDN LED does not 
light.

Poor physical connection to the 
local telephone equipment. 

Check the cables to ensure that they are securely 
connected to the appropriate ports.

If the telephone wires at your site appear to be 
satisfactory, call your local telephone company for 
assistance.

LAN STATUS

LAN port status LED is 
off (that is, not 
illuminated).

Ethernet cable is not securely 
connected.

Check the Ethernet cable connection and make sure it is 
inserted properly in a port labeled 1,2,3,or 4 on the 
back of the ISDN LAN Modem and in the Ethernet port 
on the back of your computer. Also, your computer 
should be turned on and your network software should 
be running.

Ethernet card is not set up 
properly.

Make sure your Ethernet card is set up properly (proper 
drivers are loaded). Refer to the documentation 
provided with your Ethernet card for instructions.

Summary of Contents for OfficeConnect 3C892A



































































































































Reviews:

No comments