360 Systems RC-205 Owner'S Manual Download Page 22 | Manualshive

Page: 22 / 34

background image

RC-205/210/220 Remote Control Owner's Manual Second Edition March 1997 Page

20

RC-220 Remote Control —

Full Function

The RC-220 is a full-featured Remote Control suitable for desk-top
production activities. It provides access to all DigiCart functions.

Expanded PRESET operations are available via the UTILITY MENU.

You can control up to four individual DigiCarts with the RC-220.

You can build and play Quickstacks using the MAKE PLAYLIST key.

You can access up to 16 Presets for instant playback of Cuts or Linear
Stacks.

FIND operations are available by ID number on the numeric keypad. The
STACK DIR key lends ready access to the Stack Directory.

Connecting the RC-220 to Your DigiCart(s)

The RC-220 Remote Control models uses the Serial Port 2 connector on
the rear panel of the DigiCart. Use the 9-pin interconnect cable assembly
that came with your RC-220 to connect it to the DigiCart.

DC power for the Remote Control is supplied from a small wall-mount DC
power supply. Note that this power supply should be plugged into AC
power near the DigiCart end of the cable. A short pig-tail cable with a
female coax connector exits from the 9-pin connector hood and is assigned
to receive power from the wall mount power supply.

«
...
20
21
22
23
24
...
»

Summary of Contents for RC-205



































Reviews:

No comments

Related manuals for RC-205

Brand: IBM Pages: 105

Brand: Samsung Pages: 32

Brand: Laars Pages: 28

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: IDTECK Pages: 12

Brand: Banner Pages: 2

CGLine+ Web Controller

Brand: Eaton Pages: 28

Brand: M-system Pages: 13

Brand: micro-trak Pages: 44

Brand: Atari Pages: 3

Brand: Konig Pages: 47

Brand: HEROSE Pages: 92

Saxun Mosquito Screen Lateral Door 2020

Brand: Gimenez Ganga Pages: 2

Brand: Keysight Technologies Pages: 78

Brand: Neets Control Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands