2N SmartGate User Manual Download

Page: 10 / 89

Changes

1.2

1.2 Changes

Manual
Version

Amendments to Earlier Versions

1.0.0

The User Manual applies to 2N® SmartGate FW Version 1.00A.

1.0.1

Analogue FAX support. (optionally).

1.0.2

Analogue Modem support, Network directing services support

1.0.3

Quadband version

1.0.4

Programming parameters using phone line (DTMF programming)

1.1.1

New design of manual

1.1.2

New version of PCManager (PCManagerUNI 2.04),
Digital DTMF option
AMR set on/off
Quadband version only
Free minutes option – only FW 1.5x and 3.5x

Caution



The manufacturer continuously meets customer requirements by
improving the firmware. For the latest 2N® SmartGate processor

firmware, programming tool and User Manual see

www.2n.cz



For a detailed description of the 2N® SmartGate firmware upgrade refer
to the section devoted to the PC programming tool.

Summary of Contents for SmartGate


























































































Search results

Summary of Contents for SmartGate

Reviews:

Related manuals for SmartGate

Brands by name

Popular brands

2N SmartGate, User Manual

Search results

Summary of Contents for SmartGate

Reviews:

Related manuals for SmartGate

Brands by name

Popular brands