1010music nanobox razzmatazz User Manual Download Page 66

Page: 66 / 89

P. 66 of 89

nanobox | razzmatazz User Manual

Oct 14, 2022

Available Pad Setup Options

The table below describes the Pad Setup options. Not all options apply to all pad
models.

Parameter

Description

Modulation

Target?

Excl Group

Exclusive Grouping. Triggering a pad assigned to

an exclusive group will cause any other pad in that

group to stop playing.

Options: None, Group A, Group B, Group C or

Group D

Filter mode

This controls when the filters are applied to the FM

oscillators in this pad. See the voice architecture to

get a detailed picture of where the filters are

applied. Choose Serial if you want Filter 2 applied

after Filter 1 is applied. Choose Parallel to apply

each filter separately and then combine the result.

Choose Per Osc to apply Filt 1 to FM Osc 1, and Filt 2

to FM Osc2. If you choose Per Osc, the Filter does

not get applied to the WAV.

Does not apply to Clips or Slicers.

Options: Serial, Parallel, or Per Osc.

Launch

Mode

When Launch Mode is Trigger, the clip will play

through once each time it is triggered. When

Launch Mode is Toggle, playback will continue

until another trigger event is received for the clip.

The progress bar on the clip pad will be gray when

playing the last or only loop through the clip, and

white otherwise.

Applies to Clip pads only.

Options: Trigger, Toggle

Play Thru

When Play Thru is On, the playback of the WAV will

start at the currently selected slice, and continue to

play until the end of the file. When Play Thru is Off,

playback will end at the end of the current slice.

Applies to Slicer pads only.

Options: ON, OFF

Summary of Contents for nanobox razzmatazz


























































































Search results

Summary of Contents for nanobox razzmatazz

Reviews:

Related manuals for nanobox razzmatazz

Brands by name

Popular brands

1010music nanobox razzmatazz, User Manual

Search results

Summary of Contents for nanobox razzmatazz

Reviews:

Related manuals for nanobox razzmatazz

Brands by name

Popular brands