ZyAIR G-3000 User’s Guide
Chapter 18 Firmware and Configuration File Maintenance
156
3
Enter command “sys stdio 0” to disable the SMT timeout, so the TFTP transfer will not
be interrupted. Enter command “sys stdio 5” to restore the five-minute SMT timeout
(default) when the file transfer is complete.
4
Launch the TFTP client on your computer and connect to the ZyAIR. Set the transfer
mode to binary before starting data transfer.
5
Use the TFTP client (see the example below) to transfer files between the ZyAIR and the
computer. The file name for the configuration file is
rom-0
(rom-zero, not capital o).
Note that the telnet connection must be active and the SMT in CI mode before and during the
TFTP transfer. For details on TFTP commands (see following example), please consult the
documentation of your TFTP client program. For UNIX, use “get” to transfer from the ZyAIR
to the computer and “binary” to set binary transfer mode.
18.2.4 Example: TFTP Command
The following is an example TFTP command:
TFTP [-i] host get rom-0 config.rom
where “i” specifies binary image transfer mode (use this mode when transferring binary files),
“host” is the ZyAIR IP address, “get” transfers the file source on the ZyAIR (rom-0 name of
the configuration file on the ZyAIR) to the file destination on the computer and renames it
config.rom.
The following table describes some of the fields that you may see in third party TFTP clients.
18.2.5 Backup Via Console Port
Back up configuration via console port by following the HyperTerminal procedure shown
next. Procedures using other serial communications programs should be similar.
1
Display menu 24.5 and enter “y” at the following screen.
Table 53
General Commands for Third Party TFTP Clients
COMMAND
DESCRIPTION
Host
Enter the IP address of the ZyAIR. 192.168.1.2 is the ZyAIR’s default IP
address when shipped.
Send/Fetch
Use “Send” to upload the file to the ZyAIR and “Fetch” to back up the file on
your computer.
Local File
Enter the path and name of the firmware file (*.bin extension) or configuration
file (*.rom extension) on your computer.
Remote File
This is the filename on the ZyAIR. The filename for the firmware is “ras” and for
the configuration file, is “rom-0”.
Binary
Transfer the file in binary mode.
Abort
Stop transfer of the file.
Содержание ZyAIR G-3000
