ZyXEL Communications P-871H Series Скачать руководство пользователя страница 86

Страница: 86 / 101

P-871H Series User’s Guide

Appendix A

Assuming that you have only one network card on the computer, locate the

ifconfig-

eth0

configuration file (where

eth0

is the name of the Ethernet card). Open the

configuration file with any plain text editor.

• If you have a dynamic IP address, enter

dhcp

in the

BOOTPROTO=

field. The

following figure shows an example.

Figure 66

Red Hat 9.0: Dynamic IP Address Setting in ifconfig-eth0

• If you have a static IP address, enter

static

in the

BOOTPROTO=

field. Type

IPADDR

= followed by the IP address (in dotted decimal notation) and type

NETMASK

= followed by the subnet mask. The following example shows an example

where the static IP address is 192.168.1.10 and the subnet mask is 255.255.255.0.

Figure 67

Red Hat 9.0: Static IP Address Setting in ifconfig-eth0

If you know your DNS server IP address(es), enter the DNS server information in the

resolv.conf

file in the

/etc

directory. The following figure shows an example where

two DNS server IP addresses are specified.

Figure 68

Red Hat 9.0: DNS Settings in resolv.conf

After you edit and save the configuration files, you must restart the network card. Enter

./network restart

in the

/etc/rc.d/init.d

directory. The following figure

shows an example.

DEVICE=eth0
ONBOOT=yes

BOOTPROTO=dhcp

USERCTL=no
PEERDNS=yes
TYPE=Ethernet

DEVICE=eth0
ONBOOT=yes

BOOTPROTO=static
IPADDR=

192.168.1.10

NETMASK=

255.255.255.0

USERCTL=no
PEERDNS=yes
TYPE=Ethernet

nameserver 172.23.5.1
nameserver 172.23.5.2

Содержание P-871H Series






































































































Результаты поиска

Содержание P-871H Series

Отзывы:

Похожие инструкции для P-871H Series

Бренды по названию

Популярные бренды

ZyXEL Communications P-871H Series, Руководство пользователя

Результаты поиска

Содержание P-871H Series

Отзывы:

Похожие инструкции для P-871H Series

Бренды по названию

Популярные бренды