ZyXEL Communications C2100Z Скачать руководство пользователя страница 14

14

14

Federal Communications Commission 
(FCC):

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that 
may cause undesired operation.

 

NOTE: 

This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

 

Caution

Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment.
 
For product available in the USA/Canada market, only channel 1~11 can be 
operated. Selection of other channels is not possible.

This device and it's antenna(s) must not be co-located or operating in conjunction 
with any other antenna or transmitter except in accordance with FCC multi-
transmitter product procedures.

IMPORTANT NOTE:

Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with 
minimum distance 21cm between the radiator and your body.

Содержание C2100Z


















Отзывы: