ZURN INDUSTRIES, LLC
5900 Elwin Buchanan Drive, Sanford, NC U.S.A. 27330, Ph. 1-800-997-3876, Fax 919-775-3541
In Canada:
ZURN INDUSTRIES LIMITED
7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, Ph. 905-405-8272, Fax 905-405-1292
Rev. C
Date: 10/18/2018
C.N. No. SAN008373
Prod. | Dwg. No. CF1551
PAGE 1 OF 4
AQUASPEC FAUCETS
MODEL - Z82300-XL SERIES
SINGLE CONTROL FAUCET
TECHNICAL INFORMATION
®
INSTALLATION INSTRUCTIONS
1. REMOVE SPOUT BODY (#9) FROM INTERNAL BODY (#5) BY PULLING APART.
2. SECURE GASKET (#12A) WITH ADHESIVE BACKING TO UNDERSIDE OF INTERNAL BODY (#5).
(NOTE: SKIP TO OPTIONAL 8” COVER PLATE ASSEMBLY INSTRUCTIONS IF COVER PLATE OPTION INCLUDED)
3. PLACE INTERNAL BODY (#5) ONTO SINK THROUGH PRE-DRILLED MOUNTING HOLE IN SINK. ORIENT BODY WITH
FLEX HOSES TOWARD FRONT AND MOUNTING STUD TOWARD BACK.
4. PLACE MOUNTING RING (#12C) ONTO MOUNTING STUD (#10). FLAT SIDE OF MOUNTING RING SHOULD FACE UN-
DERSIDE OF SINK. SECURE INTERNAL BODY (#5) WITH MOUNTING NUT (#12B).
5. PLACE FRICTION GASKET (#12D) OVER OUTSIDE OF INTERNAL BODY (#5).
6. PLACE SPOUT BODY (#9) OVER INTERNAL BODY (#5) AND ALIGN.
7. SECURE SPOUT BODY (#9) TO INTERNAL BODY (#5) BY CONNECTING DOMED CARTRIDGE FLANGE (#2) TO CAR-
TRIDGE RETAINING NUT (#3). USE INCLUDED DOMED CARTRIDGE FLANGE WRENCH (#12E) TO TIGHTEN.
8. INSTALL HANDLE (#1A).
8.1. REMOVE COLORED HOT/COLD INDEX (ITEM #1C) FROM HANDLE BY PRESSING OUT FROM UNDERSIDE OF
HANDLE (#1A).
8.2. LOOSEN SETS CREW (#1B) USING 1/8” ALLEN WRENCH.
8.3. SLIDE HANDLE ONTO STEM OF CERAMIC MIXING CARTRIDGE (#4).
8.4. TIGHTEN SETS CREW (#1B) USING 1/8” ALLEN WRENCH. DO NOT OVER TIGHTEN.
8.5. PRESS COLORED HOT/COLD INDEX (#1C) INTO HANDLE. IT MAY BE NECESSARY TO LUBRICATE THE O-RING
ON THE HOT/COLD INDEX TO FACILITATE ASSEMBLY.
9. ATTACH LAVATORY SUPPLIES TO BRAIDED FLEX HOSES (#11).
10. TURN SUPPLY WATER ON AND OPERATE FAUCET CHECKING FOR LEAKS.
11. INSTALL AERATOR INTO FAUCET AND HAND TIGHTEN INTO FAUCET SPOUT. IT MAY BE NECESSARY TO REMOVE
AND CLEAN THE AERATOR AT START UP.
IMPORTANT
THE WATER SUPPLY LINES MUST BE THOROUGHLY FLUSHED BEFORE INSTALLATION TO PREVENT
FOREIGN MATTER AND DEBRIS FROM CLOGGING AND/OR DAMAGING INTERNAL COMPONENTS AND THEREBY PRE-
VENTING THE FAUCET FROM FUNCTIONING PROPERLY
NOTE:
FOR PROPER PERFORMANCE, THE OPTIONAL 8” COVER PLATE ASSEMBLY MUST BE USED WHEN INSTALL-
ING THIS FAUCET ON A STAINLESS STEEL SINK
FLOW:
2.2 GPM [8.3L] PRESSURE COMPENSATING AERATOR*
MAXIMUM PRESSURE:
125 PSI
MAXIMUM TEMPERATURE:
160
O
F
CARTRIDGE STYLE - CERAMIC DISC MIXING CARTRIDGE WITH TEMPERATURE LIMIT STOP
* OTHER AERATORS AVAILABLE BY REQUEST
WARNING
: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
ADVERTENCIA:
Cáncer y daño reproductivo - www.P65Warnings.ca.gov
AVERTISSEMENT:
Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov
