ZURN INDUSTRIES, LLC
5900 Elwin Buchanan Drive, Sanford, NC U.S.A. 27330, Ph. 1-800-997-3876, Fax 919-775-3541
In Canada:
ZURN INDUSTRIES LIMITED
7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, Ph. 905-405-8272, Fax 905-405-1292
Rev. C
Date: 10/18/2018
C.N. No. SAN008373
Prod. | Dwg. No. CF1551
PAGE 2 OF 4
OPTIONAL 8” COVER PLATE ASSEMBLY
1. REMOVE 8” COVER PLATE ASSEMBLY (#13) FROM BAG AND LOCATE (13C) MOUNTING HARDWARE.
2. THREAD TWO STUDS (#13C) ONTO BOTTOM OF COVER PLATE (#13A).
3. REMOVE SPOUT BODY (#9) FROM INTERNAL BODY (#5) BY PULLING APART.
4. SECURE GASKET (#12A) WITH ADHESIVE BACKING TO UNDERSIDE OF INTERNAL BODY (#5).
5. ATTACH COVER PLATE (#13A) TO BASE OF INTERNAL BODY (#5) USING TWO #8-32 SCREWS (#13D)
6. PLACE COVER PLATE GASKET (#13B) ONTO BASE OF COVER PLATE (#13A) AND INSERT THROUGH MOUNTING
HOLES IN SINK.
7. SECURE FAUCET ASSEMBLY TO SINK USING WASHERS (#13C) AND STAINLESS STEEL NUTS (#13C).
8. FOLLOW INSTALLATION INSTRUCTIONS 4 THROUGH 11 TO COMPLETE INSTALLATION.
MAINTENANCE
1. YOUR ZURN FAUCET HAS A HIGHLY POLISHED NICKEL CHROME PLATED FINISH. CLEAN WITH SOAP AND WATER OR A
MILD CLEANER WHICH IS SAFE FOR CHROME PLATING. DO NOT USE ACIDS OR TOILET BOWL CLEANER AS THEY WILL
DAMAGE THE FINISH.
2. AQUASPEC FAUCETS CONTAIN CERAMIC MIXING CARTRIDGES WHICH REQUIRE NO MAINTENANCE. TO REMOVE AND
REPLACE THE CARTRIDGE:
2.1. REMOVE HOT/COLD INDEX BUTTON (#1C) BY CAREFULLY PRYING LOOSE FROM UNDERSIDE OF HANDLE (#1A)
2.2. LOOSEN SET SCREW (# 1B) IN HANDLE USING 1/8” ALLEN WRENCH.
2.3. REMOVE HANDLE FROM CARTRIDGE STEM
2.4. LOOSEN AND REMOVE DOMED CARTRIDGE FLANGE (# 2) USING FLANGE WRENCH (#12E) PROVIDED.
2.5. LOOSEN AND REMOVE CARTRIDGE RETAINING NUT (#3)
2.6. PULL CERAMIC MIXING CARTRIDGE (#4) BY PULLING ON STEM WHILE WIGGLING FROM SIDE-TO-SIDE
2.7. INSTALL NEW CARTRIDGE USING THE ALIGNMENT PINS FOR PROPER ORIENTATION AND PROPER SEATING IN
THE FAUCET BODY.
2.8. REINSTALL HANDLE ASSEMBLY BY REVERSING STEPS 2.1 THROUGH 2.5.
3. TEMPERATURE LIMIT ADJUSTMENT – THE Z82300-XL FAUCET MAY BE ADJUSTED TO LIMIT THE MAXIMUM OPERATING
TEMPERATURE.
3.1. REMOVE CERAMIC MIXING CARTRIDGE (#4) PER MAINTENANCE INSTRUCTIONS 2.1 THROUGH 2.6 ABOVE.
3.2. REMOVE RED TEMPERATURE LIMIT RING FROM MIXING CARTRIDGE.
3.3. ROTATE RED TEMPERATURE LIMIT RING CLOCKWISE TO INCREASE MAXIMUM TEMPERATURE OR COUNTER-
CLOCKWISE TO DECREASE MAXIMUM TEMPERATURE. RED TEMPERATURE LIMIT RING IS MARKED WITH ARROWS
AND +/- TO INDICATE DIRECTION OF ROTATION AND EFFECT ON MAXIMUM TEMPERATURE.
3.4. REPLACE RED TEMPERATURE LIMIT RING IN DESIRED ORIENTATION.
3.5. REINSTALL HANDLE ASSEMBLY BY REVERSING STEPS 2.1 THROUGH 2.5.
3.6. TEST MAXIMUM TEMPERATURE FOR ACCEPTABILITY AND REPEAT STEPS 3.1 THROUGH 3.5 IF NECESSARY.
OPTIONAL HOSE SPRAY ASSEMBLY
1. REMOVE HOSE SPRAY ASSEMBLY FROM BAG AND REMOVE PLASTIC LOCKING NUT FROM HOLDER.
2. INSERT HOLDER THROUGH SINK AND SECURE WITH PLASTIC LOCKING NUT FROM BOTTOM OF SINK. DO NOT OVER
TIGHTEN.
3. INSERT HOSE THROUGH HOLDER.
4. CONNECT HOSE END TO COUPLING (#15). IT MAY BE NECESSARY TO USE THREAD SEALER.
