background image

AquaSense

®

  EV

TM

ZEG Series

Automatic Sensor-Operated,

Hard-Wired Flushometer

Installation, Operation, Maintenance,

and Parts Manual

Patented and Patents Pending

LIMITED WARRANTY

All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the date of
purchase. Decorative finishes warranted for one year. We will replace at no costs goods that prove defective provided we are notified in writing of
such defect and the goods are returned to us prepaid at Sanford, NC, with evidence that they have been properly maintained and used in
accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or damages whatsoever, including incidental or
consequential damages. The sole and exclusive remedy shall be limited to the replacement of the defective goods. Before installation and use, the
purchaser shall determine the suitability of the product for his intended use and the purchaser assumes all risk and liability whatever in connection therewith.
Where permitted by law, the implied warranty of merchantability is expressly excluded. If the products sold hereunder are “consumer products,” the
implied warranty of merchantability is limited to a period of three years and shall be limited solely to the replacement of the defective goods. All weights
stated in our catalogs and lists are approximate and are not guaranteed.

ZEG6003EV-HW6 Flushometer
for Z5798-206-00 Low Flow
Urinal

Sensor-Operated, Hard-Wired Urinal
System

Содержание AquaSense EV ZEG Series








Отзывы: