background image

d.  When  you  hear  two  long  beep”  Beep-----  Beep-----”    means  you  are  in  the  Low  Voltage 
Cutoff Type menu, please choose your desired value by pulling the throttle stick to the lowest 
position. 
e. The system will automatically enter into next setting item when you nish one . If you do 
not want to change other settings, unplug the power to exit.

Reduce Power 

– Lower the power output 

Hard Cutoff 

– Immediately shut down the power once the voltage reaches the preset value

THE TONES WILL BE HEARD IN SEQUENCE AS FOLLOWS:

1   Beep-                                                         Brake Type  (1 short tone)
2   Beep-Beep-                                               Battery Type (2 short tone)
3   Beep-Beep-Beep-                                     Cut Off Voltage Threshold  (3 short tone)
4   Beep-Beep-Beep-Beep-                           Restore Factory Setup Defaults   (4 short tone)
5   Beep-----                                                   Motor Timing   (1 long tone)
6   Beep-----Beep-                                         SBEC Voltage Output   (1 long tone 1 short tone)
7   Beep-----Beep- Beep-                              Governor Mode (1 long tone 2 short tone)
8   Beep-----Beep- Beep- Beep-                   Motor Rotation (1 long tone 3 short tone)
9   Beep-----Beep- Beep- Beep- Beep-        Start Up Strength(1 long tone 4 short tone)
10  Beep----- Beep-----                                  Low Voltage Cut Off Type  (2 long tone)

Note :One long tone “Beep-----”is equal to ve short tone “Beep-”.

8

10.  Low Voltage Cutoff Type 

a. Turn on your radio and set the throttle stick to top positon (100%)
b. Plug the battery pack into your controller
c. Wait for 2 seconds, you will hear 4 groups of two sets of fast beeps, after this you will hear 
four single beeps to indicate you have successfully entered the programming mode

d. When you here 1 long beep and four short beeps “ Beep----- Beep- Beep- Beep- Beep” means 
you are in the Start Up Strength menu, please choose your desired value by pulling the throttle 
stick to the lowest position. 
e. The system will automatically enter into next setting item when you nish one . If you do not 
want to change other settings, unplug the power to exit.

Low(10%-15%-20%)

   low start up current

Mid (25%-30%-35%)

     start up current

High(40%-45%-50%)

     high start up current

Programming Tone Reference Table

Brake

Type

Tone of 

value

Prog.Item

BEEP-

BEEP-
BEEP-

BEEP-
BEEP-
BEEP-

BEEP-
BEEP-
BEEP-
BEEP-

BEEP-----

BEEP-----
BEEP-

BEEP-----
BEEP-
BEEP-

BEEP-----
BEEP-
BEEP-
BEEP-
BEEP-

BEEP-----
BEEP-
BEEP-
BEEP-

Brake OFF Soft Brake Mid Brake Hard Brake

Содержание Mantis 120A OPTO












Отзывы: