Zte ZXSDR R8882 L268 Скачать руководство пользователя страница 29

Страница: 29 / 65

Chapter 4 Product Installation

Make sure that the hoisting tools are fixed firmly to a fixture or a wall that can bear the

weight for the hoisting.

Use brief commands to prevent misoperation.

Plugging/Unplugging a Module

Here, modules include boards and subracks.

Caution!

Operators must wear the antistatic wrist strap.

Do not plug a module with great force lest that the pins on the backplane be bent.

Plug the module right into the slot and avoid contact between the module and the

circuit face lest that any short circuit occur.

Do not touch the module circuits, components, connectors and wiring slots when

holding a module.

RF module is very hot during operation,

so you should be careful on

plugging/unplugging.

Personnel

Caution!

Non-professionals should not maintain or debug the interior of any equipment unless

instructed by professionals on site.

Replacing the parts or modifying the equipment may give rise to extra danger. Therefore,

never replace any parts or modify the equipment by any means unless otherwise

authorized.

To ensure your safety, please contact ZTE Corporation if you have any

problem.

4.1.4 Hoisting Operation Instructions

If it is required to hoist eRRU to the tower, refer to the following instructions.

Natural conditions for hoisting operation are satisfied, such as no fog and high visibility.

The hoisting operation is prohibited in windy, snowy, or rainy days.

Tools for hoisting operation are available, such as the hoisting rope (with a bearing

capacity of 100 kg) and the crown block, and the crown block is firmly installed in

appropriate position on the tower.

Open the package to check if the cabinet is in good condition. Hoist the cabinet to the

tower after the inspection.

Perform the following steps for hoisting operation.

4-5

SJ-20110104194923-001|2011-01-19(R1.0)

ZTE Proprietary and Confidential

Содержание ZXSDR R8882 L268


































































Результаты поиска

Содержание ZXSDR R8882 L268

Отзывы:

Бренды по названию

Популярные бренды

Zte ZXSDR R8882 L268, Руководство пользователя

Результаты поиска

Содержание ZXSDR R8882 L268

Отзывы:

Бренды по названию

Популярные бренды