Zte ZXSDR R8882 L268 Скачать руководство пользователя страница 21

Страница: 21 / 65

Chapter 3 Prouduct Technical Indices

Table 3-3 FRC Parameters for Reference Sensitivity and In-channel Selectivity

Reference channel

A1-3

Allocated resource blocks

DFT-OFDM Symbols per sub-frame

Modulation

QPSK

Code rate

1/3

Payload size (bits)

2216

Transport block

CRC

(bits)

Code block CRC size (bits)

Number of code blocks

Coded block size including 12–bits trellis termination (bits)

6732

Total number of bits per sub-frame

7200

Total symbols per sub-frame

3600

3.8 Electromagnetic Compatibility

The decision rule used in this section is describes as follows:

Rule A

A communication channel is set up for the test, and it is always available during

the test.

FER of the forward channel and reverse channel are less than or equal to 1 during

the test.

When the test task accomplished, equipment under test (EUT) works normally

under pre-scheduled method, there is no information loss of user control function

and the saved data, and the communication channel is still available.

If the EUT is a transmitter only, test should be done under idle-mode, and there

is no unintentional radiation during the test.

Rule B

A communication channel is set up for the test, and it is always available during

test.

EUT works normally under pre-scheduled method, there is no information loss of

user control function and the saved data, and the communication channel is still

available.

If the EUT is a transmitter only, test should be done under idle-mode, and there

is no unintentional radiation during the test.

Rule R

There is no device damage or interference (such as software malfunction or protection

device mis-operation) during the test. The EUT works normally under the defined

boundary after transient electromagnetic incident.

3-3

SJ-20110104194923-001|2011-01-19(R1.0)

ZTE Proprietary and Confidential

Содержание ZXSDR R8882 L268


































































Результаты поиска

Содержание ZXSDR R8882 L268

Отзывы:

Бренды по названию

Популярные бренды

Zte ZXSDR R8882 L268, Руководство пользователя

Результаты поиска

Содержание ZXSDR R8882 L268

Отзывы:

Бренды по названию

Популярные бренды