Zooper Premier M Plus 48 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

Zooper Premier M Plus 48 Скачать руководство пользователя страница 10

PREMIER M PLUS 48 INSTALLATION MANUAL.

Approved Document No: GLT.MAN-120

PAGE 10

Issue : 1.2 Authorised: GH Date: 2/11/2007

5. FIELD DEVICE TERMINATION

5.1 TERMINATING THE DETECTION AND ALARM (SOUNDER) CIRCUITS.

All cables entering the enclosure should have brass cable glands, which will ensure a good ground to
the EMC enclosure coating. The Detector and Sounder circuits should be connected to the
appropriate connector block on the Termination PCB as shown in Figure 6 below.

(For detailed detector and alarm circuit wiring diagrams, please refer to pages 4 and 5.

FS

FS

FS

FS

FS

FS

ZONES

1 TO 8

BUILT IN

ZONES

9 TO 16

BUILT IN

ZONES

17 TO 24

BUILT IN

ZONES

25 TO 32

BY ADD ON

CARD

ZONES

33 TO 40

BY ADD ON

CARD

ZONES

41 TO 48

BY ADD ON

CARD

BRASS GLANDS

MAKE SURE ANY SPARE

ENTRY HOLES ARE

COVERED WITH THE

RUBBER GROMMETS

PROVIDED

Figure 6: Detector and Sounder Circuit Connection

5.2 AUXILIARY INPUT AND OUTPUT TERMINATIONS

Connect auxiliary input and output cables to the appropriate connector block terminals on the
Termination PCB (See Page 15). Screened cables should be terminated as per figure 6.

For a full description of the inputs and outputs available on the Premier M 48 range of Fire Panels,
including typical wiring diagrams please refer to pages 5 & 6

«
...
8
9
10
11
12
...
»

Содержание Premier M Plus 48























Отзывы:

Нет отзывов