Zoom B2.1u Скачать руководство пользователя страница 35

Страница: 35 / 41

ZOOM B2.1u

Specifications

Effect types

Effect modules

Max. 9 simultaneous modules

Patches

User area: 10 patches x 4 banks
Preset area: 10 patches x 4 banks

Sampling frequency

96 kHz

A/D converter

24 bit, 64 times oversampling

D/A converter

24 bit, 128 times oversampling

Signal processing

32 bit

Frequency response

20 Hz – 40 kHz +1 dB -3 dB
(with 10 kilohms load)

Display

2-digit 7-segment LED
Parameter LEDs,
Pedal assign LEDs

Input

Standard mono phone jack

Rated input level

-20 dBm

Input impedance

1 megohm

Output

Standard stereo phone jack
(doubles as line and headphone jack)

Maximum output level

+5 dBm (output load impedance
10 kilohms or more)

Maximum phones output level

20 mW + 20 mW
(into 32 ohms load)

XLR jack (balanced output)

Input/output gain

0 dB

Output impedance

100 ohms
(HOT-GND)
(COLD-GND)
200 ohms
(HOT-COLD)

Control input

For FP02 (FP01) /FS01

USB interface

PC interface:

16-bit (stereo configuration for
recording/playback)

Sampling frequency:

32 kHz, 44.1 kHz, 48 kHz

Power requirements

AC adapter

9 V DC, 300 mA (center minus
plug) (ZOOM AD-0006)

Batteries

Four IEC R6 (size AA) batteries,
Approx. 6 hours continuous
operation (alkaline batteries)

Dimensions

165 mm (D) x 255 mm (W) x
79mm (H)

Weight

1200 g (without batteries)

Options

Expression pedal FP02/
Foot switch FS01

• 0 dBm = 0.775 Vrms
• Design and specifications subject to change without

notice.

Troubleshooting

●

No power

Refer to "Turn power on" on page 8.

●

Reverb effect does not operate

While a rhythm pattern is playing, the reverb
effect is not available. Stop the rhythm pattern
first (

→

p. 12).

●

No effect processing occurs (when
using [BALANCED OUT] connector)

Check whether the [PRE/POST] switch is set to
POST (signal after effect processing).

●

High level of noise

Is ZOOM AC adapter being used? Be sure to use

only adapter for 9 V DC, 300 mA with center
minus plug (ZOOM AD-0006).

●

High-level noise is heard (when using
[BALANCED OUT] connector)

A ground loop may have been created among
connected devices. Check whether setting the
[GROUND] switch to "LIFT" results in an
improvement.

●

Battery life is short

Are manganese batteries being used? The use of
alkaline batteries is recommended.

Содержание B2.1u










































Результаты поиска

Содержание B2.1u

Отзывы:

Похожие инструкции для B2.1u

Бренды по названию

Популярные бренды

Zoom B2.1u, Руководство по эксплуатации

Результаты поиска

Содержание B2.1u

Отзывы:

Похожие инструкции для B2.1u

Бренды по названию

Популярные бренды