Zoom ADSL X4 Скачать руководство пользователя | Manualshive

Страница: 58 / 64

background image

58

X5

ADSL Modem User’s Manual

message. Facsimile modem boards manufactured on and after December 13, 1995,

must comply with the requirements of this section.

This equipment cannot be used on public coin phone service provided by the
telephone company. Connection to Party Line Service is subject to state tariffs.

Contact your state public utility commission, public service commission, or

corporation commission for more information.

U.S. FCC Part 15 Emissions Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

The manufacturer declares under sole responsibility that this equipment is

compliant to Directive 1999/5/EC (R&TTE Directive) via the following:

Directive

Standard

Test Report

73/23/EEC-Low
Voltage

IEC 60950: 3

rd

ed. 1999

electrical safety

89/336/EEC-EMC

EN 55024: 1998

ed

EMC-immunity

89/336/EEC-EMC

EN 55022 : 1998

ed

;

EN 61000-3-2:1998

ed

; A1, A2;

EN 61000-3-3: 1995

ed

EMC-emissions

This product is CE Marked.

Electrostatic Discharge Statement

The unit may require resetting after a severe electrostatic discharge event.

Additional compliance information is located on the CD.

«
...
56
57
58
59
60
...
»

Содержание ADSL X4

































































Отзывы:

Нет отзывов

Похожие инструкции для ADSL X4

Бренд: VisionTek Страницы: 6

Бренд: CalAmp Страницы: 62

Бренд: Kathrein Страницы: 8

Бренд: TeleWell Страницы: 131

Бренд: Clean Logix Страницы: 9

Бренд: DataComm Страницы: 39

Бренд: THOMSON Страницы: 46

Бренд: Sprint Страницы: 32

Бренд: Datatronics Страницы: 116

Бренд: Technicolor Страницы: 14

Бренд: TECOM Страницы: 17

Бренд: Tecnet Страницы: 2

Бренд: CTC Union Страницы: 19

Бренд: CTC Union Страницы: 29

Бренд: AmazonBasics Страницы: 17

DGFV338 - ProSafe Wireless ADSL Modem VPN Firewall Router

Бренд: NETGEAR Страницы: 2

Бренд: Paradise Datacom Страницы: 231

Бренд: iiNet Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды