Zoom ADSL X4 Скачать руководство пользователя страница 53

Страница: 53 / 64

Appendix D: Macintosh and Linux Users: Configuring TCP/IP Settings

Click Save and close the Network pane.

Linux TCP/IP Settings

The instructions for setting up boot-time DHCP vary dramatically
by distribution, so you may want to refer to your particular

version’s documentation.

Note:

If you have other network cards installed, you will need to

pick distinct Ethernet identifiers for each (eth0, eth1, eth2,

etc.). If you select an identifier other than eth0 for your
ADSL modem, use that identifier throughout.

For RedHat

Edit or create /etc/sysconfig/network-scripts/ifcfg-eth0 so

that it contains the following three lines:

DEVICE=eth0

ONBOOT=yes
BOOTPROTO=dhcp

If you want to use a static IP address—for example, if you were
setting up a virtual server (page 22) or a DMZ (page 25)—you
would edit or create /etc/sysconfig/network-scripts/ifcfg-eth0

so that it contains the following lines:

DEVICE=eth0

ONBOOT=yes
BOOTPROTO=static

Содержание ADSL X4

































































Результаты поиска

Содержание ADSL X4

Отзывы:

Бренды по названию

Популярные бренды

Zoom ADSL X4, Руководство пользователя

Результаты поиска

Содержание ADSL X4

Отзывы:

Бренды по названию

Популярные бренды