background image

4/10/2019

V4 User Manual and Installation Guide – Zonar Systems Support

https://support.zonarsystems.net/hc/en-us/articles/360017847851-V4-User-Manual-and-Installation-Guide

27/27

located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with
antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Use only supplied and approved antennas. Use of unauthorized antennas or modifications could impair signal quality,
void your warranty and/or result in violation of FCC regulations.

FCC Compliance Statement (Part 15.19), IC Compliance Statement (RSS-210)

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada (IC). Operation is subject to the
following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warranty And Legal Notices

For more information regarding Zonar Warranty and Legal Notices, see the 

Zonar Product Warranty

 page on our

website (

https://support.zonarsystems.net

).

Содержание V4




























Отзывы: