
Replacement Part Installation
9650-000278-01 Rev. B
ZOLL 330 Multifunction Aspirator Service Manual
3–25
5
Disconnect USB Cable from UIM Stack Assembly
6
Remove the two 6-32x 5/16 screws that secure the UIM Stack Assembly to the front
case. Carefully disconnect the J4 UIM Stack Assembly connector from the UIM
Adapter Board J1 connector while pulling the UIM Stack Assembly from the front
case. Save these screws.
7
Disconnect LCD cable from UIM Adapter Board J2 connector
8
Disconnect the ribbon cable form the UIM Adapter Board J3 connector
9
Disconnect the buzzer cable from the UIM Adapter board J4 connector
10
Remove the two 4-40 x 1/4 screws the secure the UIM Adapter Board to the front
case assembly and then remove the UIM Adapter Board.
11
Install the new UIM Adapter Board. Clean screws and apply Vibra-Tite to each of the
4-40 x 1/4 screws, insert the screws and tighten.
Torque: 3.5 in lbs
Bit Size: #1 Phillips
12
Reconnect LCD ribbon cable to the UIM Adapter Board J2 Connector.
13
Reconnect the ribbon cable to the UIM Adapter Board J3 connector.
14
Reconnect the Buzzer cable to the UIM Adapter Board J4 connector.
15
Reconnect UIM Stack Assembly by mating the UIM Stack Assembly J4 connector with
the UIM Adapter cable J1 connector. Clean screws and apply Vibra-Tite to each of the
6-32 x 5/16 screws, insert the screws, and tighten.
Torque: 5 in lbs
Bit Size: #2 Phillips
16
Reconnect the USB cable to the UIM Stack Assembly. Make sure that it “locks” into
place.
17
Re-install the front case assembly. Clean screws and apply Vibra-Tite to the two 4-40
x 1/4 screws, insert the screws into the center of the dovetail mounting bracket and
tighten.
Torque: 5 in lbs
Bit Size: #1 Phillips
18
Reconnect the ribbon cable to the PIM board, and then press down on the two locking
tabs (ears) to lock down the cable connector.
19
Attach the back cover to the aspirator module and align cover with handle, exhaust
muffler housing, and dovetail mounting studs.
Clean screws and apply Vibra-Tite to each screw, then insert and loosely thread
screws in a crossing pattern. Tighten screws in a crossing pattern, and then tighten
the two 10-32 Keps nuts and the four 6-32 x 2” screws.
Torque: 6-32 x 2” screws to 9 in lbs, 10-32 Keps Nuts to 18 in lbs
Bit Size: #2 Phillips for screws. 3/8 in nut driver
Step
Action
Содержание 330
