background image

2

© Copyright 2015 Zoeller

®

 Co. All rights reserved.

Performance Data

Limited Warranty 

etc. in all pumping applications.  The warranty set out in the paragraph above 

is in lieu of all other warranties expressed or implied; and we do not authorize 

any representative or other person to assume for us any other liability in con-

nection with our products.

Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky  40211, 

Attention: Customer Service Department to obtain any needed repair or replace-

ment of part(s) or additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, CON-

SEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED 

OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS 

FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE 

LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, 

so the above limitation may not apply to you. Some states do not allow the 

exclusion or limitation of incidental or consequential damages, so the above 

limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights 

which vary from state to state.

013859XP

Each Zoeller X600 Series Pump installation is required to have a completed Zoeller Pump Company Start-up Report (FM0990). The report is to be completed 

by an approved Start-up Technician in the presence of the installing contractor. A copy of this report will be on file at the Zoeller Pump Company offices in 

Louisville, KY.  

Failure to comply with the requirement will void the warranty agreement.

Manufacturer warrants, to the purchaser and subsequent owner during the 

warranty period, every new product to be free from defects in material and 

workmanship under normal use and service, when properly used and main-

tained, for a period of one year from date of purchase by the end user, or 18 

months from date of original manufacture of the product, whichever comes first.  

Parts that fail within the warranty period, one year from date of purchase by the 

end user, or 18 months from the date of original manufacture of the product, 

whichever comes first, that inspections determine to be defective in material or 

workmanship, will be repaired, replaced or remanufactured at Manufacturer's 

option, provided however, that by so doing we will not be obligated to replace 

an entire assembly, the entire mechanism or the complete unit.  No allowance 

will be made for shipping charges, damages, labor or other charges that may 

occur due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty for any material 

or product that has been disassembled without prior approval of Manufacturer, 

subjected to misuse, misapplication, neglect, alteration, accident or act of 

nature; that has not been installed, operated or maintained in accordance with 

Manufacturer's installation instructions; that has been exposed to outside sub-

stances including but not limited to the following:  sand, gravel, cement, mud, 

tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other 

abrasive or corrosive substances, wash towels or feminine sanitary products, 

X611

X621

X631

X641 

(1 PH)

X641

X651 

(1 PH)

X651

X661

MODEL

MODEL

PUMP PERFORMANCE CURVE

MODELS X611/X621/X631/X641/X651/X661

X611 X621

X631

X641

X651

X661

X641  1 PH

X651  1 PH

Содержание X600 Series









Отзывы: